Toyota Corolla Cross: Smart Key System (for Start Function, Gasoline Model)
Toyota Corolla Cross (2022-2024) Service Manual / Vehicle Interior / Theft Deterrent / Keyless Entry / Smart Key System (for Start Function, Gasoline Model)
- Precaution
- Parts Location
- System Diagram
- How To Proceed With Troubleshooting
- Customer Problem Analysis Check
- Check For Intermittent Problems
- Operation Check
- Registration
- Customize Parameters
- Problem Symptoms Table
- Terminals Of Ecu
- Data List / Active Test
- Diagnostic Trouble Code Chart
- IG Circuit Short to Ground (B227111)
- ACC Circuit Short to Ground (B227411)
- Engine/Power Switch Signal Compare Failure (B227862)
- Vehicle Speed Signal Circuit Open (B228231,B228262)
- Steering Lock Position Signal Compare Failure (B228562)
- Battery Circuit or Ground Circuit Energization Malfunction (B228B00)
- Wireless Starter Component Internal Failure (B277A96)
- Steering Lock System Missing Message (B278187,B278196,B278211,B278215,B279F1C)
- Antenna Coil Circuit Voltage Out of Range (B27841C)
- ID-BOX Component Internal Failure (B278D96)
- Immobiliser Amp Missing Message (B278E87)
- ID-BOX Calibration / Parameter Memory Failure (B279046)
- Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid (B279986)
- Engine Immobiliser System Circuit Short to Battery (B279A12)
- Engine Immobiliser System Incorrect Assembly (B279C95)
- Front Floor Electrical Key Oscillator Circuit Open (B27A513)
- Rear Floor 2 Electrical Key Oscillator Circuit Open (B27A713)
- Crankshaft Position Sensor "A" Signal Compare Failure (P033562)
- Brake Switch "A" Signal Compare Failure (P057162)
- Lost Communication with Brake System Control Module Missing Message (U012987,U014087,U015587,U111787)
- Engine does not Start
- Power Source Mode does not Change to ON (IG and ACC)
- Power Source Mode does not Change to ON (IG)
- Power Source Mode does not Change to ON (ACC)
- New Key cannot be Registered
- Additional Key cannot be Registered
- New Key Registration Warning Message is not Displayed
- System Malfunction Message is Displayed on the Multi-information Display
- Security Indicator Light Does not Blink
- Immobiliser System does not Operate Properly
READ NEXT:
Precaution
PRECAUTION PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE (-) AUXILIARY BATTERY TERMINAL
NOTICE: After the ignition switch is turned off, there may be a waiting time before disconnecting the negat
Parts Location
PARTS LOCATION ILLUSTRATION
*1 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)
*2 NO. 1 ENGINE ROOM RELAY BLOCK
- IGP-MAIN RELAY
*3 PARK/NEUTRAL POSITION SWITCH
*4
System Diagram
SYSTEM DIAGRAM SMART KEY SYSTEM (for Start Function)
SMART KEY SYSTEM (for Entry Function)
Click here
SEE MORE:
On-vehicle Inspection
ON-VEHICLE INSPECTION PROCEDURE
1. INSPECT DRIVER SEAT BELT WARNING LIGHT HINT: The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.
(a) Turn the ignition switch off. (b) Turn the ignition switch to ON.
(c) When the driver sea
Lost Communication with ECM/PCM "A" Missing Message (U010087,...,U110387)
DESCRIPTION
These DTCs are stored if there is a malfunction in the CAN communication
system connected to the clearance warning ECU assembly.
HINT:
If CAN communication system DTCs are stored, they may also be stored
in other systems.
DTC No.
Detection Item
DT
© 2020-2024 Copyright www.tcorollacross.com
