Toyota Corolla Cross Owners & Service Manuals

Toyota Corolla Cross: New Key Registration Warning Message is not Displayed

DESCRIPTION

If the new key registration warning message is not displayed after an electrical key transmitter sub-assembly has been registered, there may be communication problem between the certification ECU (smart key ECU assembly) and combination meter assembly (meter ECU).

CAUTION / NOTICE / HINT

NOTICE:

  • When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
  • The smart key system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Start Function) after confirming that the communication systems are functioning properly.

    Click here

  • Before replacing the certification ECU (smart key ECU assembly), refer to Registration.

    Click here

  • After repair, confirm that no DTCs are output.
  • Check that there are no electrical key transmitter sub-assemblies in the vehicle.
  • When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

PROCEDURE

1.

CHECK FOR DTC

(a) Check for DTCs.

Body Electrical > Smart Key > Trouble Codes

Result

Proceed to

DTCs are not output

A

DTCs are output

B

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

A

2.

READ VALUE USING GTS (FR DOOR COURTESY SWITCH STATUS)

(a) Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

FR Door Courtesy Switch Status

Front door RH courtesy light switch signal

Close or Open

Close: Front door RH closed

Open: Front door RH open

-

Body Electrical > Main Body > Data List

Tester Display

FR Door Courtesy Switch Status

Result

Proceed to

On the GTS screen, ON or OFF is displayed accordingly.

A

On the GTS screen, ON or OFF is not displayed accordingly.

B

B

GO TO LIGHTING SYSTEM

A

3.

CHECK METER / GAUGE SYSTEM

(a) With the electrical key transmitter sub-assembly in the vehicle and all of the doors closed, lock the doors using the entry lock function and check that the warning message is displayed on the multi-information display.

NOTICE:

In order to prevent the electrical key transmitter sub-assembly from being locked inside the vehicle, perform this inspection with the window of a door open.

HINT:

Key lock-in prevention function (vehicle interior).

Click here

Result

Proceed to

The warning message is displayed on the multi-information display.

A

The warning message is not displayed on the multi-information display.

B

B

REPLACE COMBINATION METER ASSEMBLY

A

4.

ADDITIONAL KEY REGISTRATION

(a) Clear all of the registered electrical key transmitter sub-assemblies except one and perform registration again.

Click here

NEXT

5.

CHECK MULTI-INFORMATION DISPLAY

(a) With all of the doors closed, lock the doors using the entry lock function.

(b) Unlock the doors using the entry unlock function, open the driver door and check that the warning message is displayed on the multi-information display.

Result

Proceed to

The warning message is displayed on the multi-information display.

A

The warning message is not displayed on the multi-information display.

B

A

END (10 DAYS MAY HAVE ELAPSED SINCE AN ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY WAS REGISTERED)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    READ NEXT:

     System Malfunction Message is Displayed on the Multi-information Display

    SYSTEM DESCRIPTION If an abnormal vehicle speed information is detected by the certification ECU (smart key ECUassembly), a system malfunction message is displayed on the multi-information display. WI

     Security Indicator Light Does not Blink

    DESCRIPTION The certification ECU (smart key ECU assembly) blinks the security indicator light (combination meter assembly) when the immobiliser is set (ignition switch off). The certificati

     Immobiliser System does not Operate Properly

    DESCRIPTION The immobiliser function compares the ID code that is registered in the certification ECU (smart key ECU assembly) with the ID code of the transponder chip that is embedded in the electric

    SEE MORE:

     Motor Electronics Coolant Temperature Sensor Circuit Short to Ground (P0A0011,P0A0015)

    DESCRIPTION Refer to the description for DTC P0A001C. Click here DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate Note P0A0011 Motor Electronics Coolant Temperature Sensor Circuit Short to Ground Short to ground de

     Check Bus 4 Line

    DESCRIPTION Symptom Trouble Area There are ECUs or sensors that display a communication stop on the bus diagnostic screen. Or, there are ECUs or sensors that display communication stop history on the "Detail" screen. CAN main

    © 2020-2024 Copyright www.tcorollacross.com