Toyota Corolla Cross Owners & Service Manuals

Toyota Corolla Cross: ID-BOX Component Internal Failure (B278D96)

Toyota Corolla Cross (2022-2024) Service Manual / Vehicle Interior / Theft Deterrent / Keyless Entry / Smart Key System (for Start Function, Gasoline Model) / ID-BOX Component Internal Failure (B278D96)

DESCRIPTION

When the certification ECU (smart key ECU assembly) detects an input signal indicating that the vehicle is equipped with an ID code box even though the ID code box is not registered, the certification ECU (smart key ECU assembly) stores this DTC.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Note

B278D96

ID-BOX Component Internal Failure

One of the following conditions is met:

  • The certification ECU (smart key ECU assembly) recognizes that the wire harness judging whether the vehicle is equipped with an ID code box or not is provided even though the ID code box is not registered.
  • The certification ECU (smart key ECU assembly) receives a LIN signal from the ID code box even though the ID code box is not registered.
  • The certification ECU (smart key ECU assembly) receives a LIN signal from the ID code box even though the wire harness judging whether the vehicle is equipped with an ID code box or not is not provided.

Misconnection of the ID code box

DTC output confirmation operation:

  • Always
Vehicle Condition and Fail-safe Operation when Malfunction Detected

Vehicle Condition when Malfunction Detected

Fail-safe Operation when Malfunction Detected

Key registration will be prohibited

-
Related Data List and Active Test

DTC No.

Data List and Active Test

B278D96

-

CAUTION / NOTICE / HINT

NOTICE:

  • When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
  • The smart key system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Start Function) after confirming that the communication systems are functioning properly.

    Click here

  • Before replacing the certification ECU (smart key ECU assembly), refer to Registration.

    Click here

  • After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."

PROCEDURE

1.

CLEAR DTC

(a) Clear the DTCs.

Body Electrical > Smart Key > Clear DTCs
NEXT

2.

CHECK DTC OUTPUT

(a) Check for DTCs.

Body Electrical > Smart Key > Trouble Codes

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

OK:

DTC B278D96 is not output.

OK

END
NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    READ NEXT:

     Immobiliser Amp Missing Message (B278E87)

    DESCRIPTION A transponder key amplifier is built into the certification ECU (smart key ECU assembly). When a communication malfunction occurs with the transponder key amplifier inside the certificat

     ID-BOX Calibration / Parameter Memory Failure (B279046)

    DESCRIPTION When an internal malfunction occurs in the ID code box (immobiliser code ECU), the certification ECU (smart key ECU assembly) stores this DTC. DTC No. Detection Item DTC Detec

     Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid (B279986)

    DESCRIPTION If there is a communication malfunction between the ECM and ID code box (immobiliser code ECU), or when the communication ID codes do not match, the ECM stores this DTC. DTC No. De

    SEE MORE:

     Front Passenger Side Power Window Switch

    RemovalREMOVAL CAUTION / NOTICE / HINT COMPONENTS (REMOVAL) Procedure Part Name Code 1 POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL - - - 2 POWER WINDOW REGULATOR SWITCH ASSEMBLY 84810 - -

     On-vehicle Inspection

    ON-VEHICLE INSPECTION CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The following procedure is for the LH side. PROCEDURE 1. REMOVE FRONT WHEEL Click here 2. SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY Click here 3. REMOVE FRONT DISC Click he

    © 2020-2024 Copyright www.tcorollacross.com