Toyota Corolla Cross: Check For Intermittent Problems
CHECK FOR INTERMITTENT PROBLEMS
NOTICE:
- Operation history is stored in the RAM or EEPROM of the certification ECU (smart key ECU assembly). As the cause of a malfunction stored in the RAM will be cleared when the cable is disconnected from the negative (-) auxiliary battery terminal, do not disconnect the cable from the negative (-) auxiliary battery terminal before checking and recording are complete.
- If the vehicle or vehicle controls are operated (for example, during initial inspection when the vehicle is brought in for repair) before operation history has been read and saved, the operation history information could be lost.
- The operation history function uses the current system time of the GTS and the time counter inside the controlling ECU to calculate the time shown in the operation history. For this reason, before reading the operation history, first make sure that the GTS system clock is accurately set to the current time.
VEHICLE CONTROL HISTORY (ROB)
HINT:
The certification ECU (smart key ECU assembly) stores the vehicle control history (RoB) of the smart key system and it can be read using the GTS.
(a) Read the Vehicle Control History (RoB) according to the display on the GTS.
Body Electrical > Smart Key > Utility|
Tester Display |
|---|
| Vehicle Control History (RoB) |
|
Code | Item List |
Item Description | Note |
|---|---|---|---|
|
X0A10 | Auto Entry Mode Switch History |
The certification ECU mode changed when the GTS was connected. |
- |
| X0A11 |
Customize (Auto Entry Cancel) |
The smart functionality was canceled via customization. |
- |
| X0A12 |
Engine Start (Inactive) | Engine could not be started because steering lock status was unlock not confirmed. |
- |
| X0A13 |
Engine Start | Engine could not be started because immobiliser was set. |
- |
| X0A14 |
Radio Wave Interference (RF Reception Not Available) |
An attempt was made to start the engine without a key. |
- |
| X0A15 |
Engine Start Inactive (Steering Lock System) |
Engine could not be started because steering lock lever was engaged. |
- |
| X0A18 |
Auto Entry Wireless Operation History (Lock/Unlock) |
Lock/unlock was performed by wireless operation. |
- |
| X0A19 |
Auto Entry Wireless Operation History (Open/Close) |
Power slide door/back door was opened/closed by wireless operation. |
- |
| X0A1A |
Warning Operation History | Warning operation was performed by a function of the certification ECU. |
- |
| X0A1B |
Registration Function (Reason for Non-operation) |
The reason that key registration failed. |
- |
| X0A1C |
Radio Wave Interference (RF Signal Received) |
Smart system did not operate due to effects of radio frequency interference. |
- |
| X0A1D |
Auto Entry Lock (Inactive) |
The reason that entry lock did not operate. |
- |
| X0A1E |
Auto Entry Unlock (Inactive) |
The reason that operations other than entry lock operation did not operate correctly. |
- |
HINT:
Some items may not be displayed depending on the specifications of the vehicle.
(b) Read the Vehicle Control History (RoB) according to the display on the GTS.
Body Electrical > Power Source Control > Utility|
Tester Display |
|---|
| Vehicle Control History (RoB) |
|
Code | Item List |
Item Description | Note |
|---|---|---|---|
|
X0A00 | Cause Details of Engine Start / READY ON Failure |
The reason that engine didnot start. |
- |
| X0A01 |
Cause Details of Engine Stop / READY OFF in IG ON |
The reason that enginestalled or engine stopped. |
- |
| X0A02 |
Cause Details of Leave ACC ON / IG ON |
The reason that vehicle power source turned off automatically. |
- |
HINT:
Some items may not be displayed depending on the specifications of the vehicle.
SYMPTOM SIMULATION
Click here .gif)
READ NEXT:
Operation Check
OPERATION CHECK CHECK CUSTOMIZE PARAMETERS (a) The operation check below is based on the non-customized initial condition of the vehicle. (However, make sure that "ACC Customize" is set to "ON" using
Registration
REGISTRATION PROCEDURE 1. REPAIR INSTRUCTION
CAUTION: As weak radio waves are emitted from the electrical key transmitter sub-assembly, if a pacemaker is being used, be sure to read the pacemaker in
Customize Parameters
CUSTOMIZE PARAMETERS CUSTOMIZE SMART KEY SYSTEM (for Start Function)
NOTICE:
When the customer requests a change in a function, first make sure that the function can be customized.
Record t
SEE MORE:
Stopping the engine
1. Stop the vehicle completely.
2. Set the parking brake, and shift the shift
lever to P.
Check the parking brake indicator
is illuminated.
Do not press the shift lever button
after shifting the shit position to P.
3. Press the engine switch.
The engine will stop, and the meter
display will be ex
Under Hood
UNDER HOOD
GENERAL NOTES
Maintenance requirements vary depending on country.
Check the maintenance schedule in the owner's manual.
Following the maintenance schedule is mandatory.
Determine the appropriate time to service the vehicle using either miles
driven or time (months) el
