Toyota Corolla Cross: Evaporative Emission System Pressure / Intake Air Pressure Signal Compare Failure (P106A62,P106C62)

DESCRIPTION

Those DTCs are designed to detect a deviation in the output characteristics of a pressure sensor.

*: Data List name

MONITOR DESCRIPTION

Those DTCs are stored when a deviation from pressure sensor characteristics is detected.

The pressure sensors* are checked approximately 50 minutes after the ignition switch is turned off. If the pressures detected by the pressure sensors* differ by a certain amount, the MIL is illuminated and a DTC is stored (2 trip detection logic).

HINT:

• *: P106A62 checks the canister pressure sensor and the manifold absolute pressure sensor. P106C62 checks the canister pressure sensor and atmospheric pressure sensor.
• Correct judgment may not be possible when the altitude is 4000 m (13120 ft.) or more.

MONITOR STRATEGY

TYPICAL ENABLING CONDITIONS

TYPICAL MALFUNCTION THRESHOLDS

CONFIRMATION DRIVING PATTERN

HINT:

• After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

  Click here

• When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.

  Click here

1. Connect the GTS to the DLC3.
2. Turn the ignition switch to ON.
3. Turn the GTS on.
4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
5. Turn the ignition switch off and wait for at least 30 seconds.
6. Start the engine and idle for 10 seconds or more [A].
7. Turn the ignition switch off.
8. Leave the ignition switch off for 55 minutes [B].
9. Turn the ignition switch to ON.
10. Turn the GTS on.
11. Enter the following menus: Powertrain / Engine / Trouble Codes [C].
12. Read the pending DTCs.

    HINT:

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
13. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
14. Input the DTC: P106A62 or P106C62.
15. Check the DTC judgment result.

    GTS Display	Description
    NORMAL	DTC judgment completed System normal
    ABNORMAL	DTC judgment completed System abnormal
    INCOMPLETE	DTC judgment not completed Perform driving pattern after confirming DTC enabling conditions

    HINT:

    • If the judgment result is NORMAL, the system is normal.
    • If the judgment result is ABNORMAL, the system is malfunctioning.
    • If the judgment result is INCOMPLETE, perform steps [A] through [C] again.
    • [A] to [C]: Normal judgment procedure.

      The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.

    • When clearing the permanent DTCs, do not disconnect the cable from the auxiliary battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.

CAUTION / NOTICE / HINT

HINT:

• Refer to "Data List / Active Test" [Atmospheric Pressure, Intake Manifold Absolute Pressure and Vapor Pressure Pump].

  Click here

• Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

(a) Read the DTCs.

HINT:

If any DTCs other than P106A62 and/or P106C62 are output, troubleshoot those DTCs first.

B

GO TO STEP 3

C

GO TO STEP 4

D

GO TO DTC CHART

A

Click here

NEXT

GO TO STEP 5

Click here

NEXT

GO TO STEP 5

for 2WD: Click here

for AWD: Click here

NEXT

(a) Clear the DTCs.

(b) Turn the ignition switch off and wait for at least 30 seconds.

NEXT

(a) Enter the following menus.

(b) Confirm that the difference between Intake Manifold Absolute Pressure and Vapor Pressure Pump is 7.23 kPa (1.04 psi) or less.

(c) Confirm that the difference between Atmospheric Pressure and Vapor Pressure Pump is 10 kPa (1.45 psi) or less.

NEXT

END

READ NEXT: