Toyota Corolla Cross: Hybrid/EV Battery Energy Control Module Unexpected Operation (P0A1F94)
DTC SUMMARY
MALFUNCTION DESCRIPTION
The hybrid vehicle control ECU (main CPU) monitors the battery ECU assembly.
The cause of this malfunction may be the following:
Battery ECU assembly internal malfunction- Battery ECU assembly malfunction
DESCRIPTION
The hybrid vehicle control ECU (main CPU) monitors the battery ECU assembly and stores this DTC when it detects a malfunction.
|
DTC No. | Detection Item |
DTC Detection Condition |
Trouble Area | MIL |
Warning Indicate | Note |
|---|---|---|---|---|---|---|
|
P0A1F94 | Hybrid/EV Battery Energy Control Module Unexpected Operation |
The battery ECU assembly value received by the hybrid vehicle control ECU (main CPU) exceeds the threshold for a certain period of time. (1 trip detection logic) |
Battery ECU assembly |
Comes on | Master Warning: Comes on | SAE Code: P0A1F |
MONITOR DESCRIPTION
The battery ECU assembly monitors the hybrid vehicle control ECU via CAN communication. If the battery ECU assembly detects a malfunction in the hybrid vehicle control ECU, it will illuminate the MIL and store a DTC.
MONITOR STRATEGY
|
Related DTCs | P0A1F (INF P0A1F94): Battery Energy Control Module |
|
Required sensors/components | Battery ECU assembly |
|
Frequency of operation | Continuous |
|
Duration | TMC's intellectual property |
|
MIL operation | 1 driving cycle |
|
Sequence of operation | None |
TYPICAL ENABLING CONDITIONS
|
The monitor will run whenever the following DTCs are not stored |
TMC's intellectual property |
|
Other conditions belong to TMC's intellectual property |
- |
TYPICAL MALFUNCTION THRESHOLDS
|
TMC's intellectual property | - |
COMPONENT OPERATING RANGE
|
Hybrid vehicle control ECU | P0A1F (INF P0A1F94) is not detected |
CONFIRMATION DRIVING PATTERN
HINT:
- After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
.gif)
- When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
- Connect the GTS to the DLC3.
- Turn the ignition switch to ON and turn the GTS on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the ignition switch off and wait for 2 minutes or more.
- Turn the ignition switch to ON and turn the GTS on.
- Turn the ignition switch to ON (READY) and wait for 10 seconds or more. [*1]
HINT:
[*1] : Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
- Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE, perform the normal judgment procedure again.
PROCEDURE
|
1. | CHECK DTC OUTPUT (HYBRID CONTROL) |
(a) Check for DTCs.
Powertrain > Hybrid Control > Trouble Codes|
Result | Proceed to |
|---|---|
|
P0A1F94 only is output. |
A |
| DTCs except P0A1F94 are output. |
B |
(b) Turn the ignition switch off.
| A | .gif) | REPLACE BATTERY ECU ASSEMBLY |
| B | | GO TO DTC CHART (HYBRID CONTROL SYSTEM) |
READ NEXT:
Drive Motor "B" Temperature Sensor Circuit Short to Ground (P0A3011,P0A3015)
DTC SUMMARY MALFUNCTION DESCRIPTION These DTCs are stored when the rear motor temperature sensor output is abnormal. The cause of this malfunction may be one of the following: Hybrid vehicle control E
Drive Motor "B" Temperature Sensor Signal Stuck In Range (P0A302A)
DTC SUMMARY MALFUNCTION DESCRIPTION This DTC is stored when the rear motor temperature sensor output is abnormal.
The cause of this DTC output may be the following: Rear motor temperature sensor ma
Inverter "A" Cooling System Performance (P0A9300)
DTC SUMMARY MALFUNCTION DESCRIPTION This DTC indicates when the temperature sensor value inside the inverter has become abnormal. The cause of this malfunction may be one of the following: Internal in
SEE MORE:
On-vehicle Inspection
ON-VEHICLE INSPECTION PROCEDURE
1. INSPECT ACCELERATOR PEDAL SENSOR ASSEMBLY (a) Connect the GTS to the DLC3.
(b) Turn the power switch on (IG). (c) Turn the GTS on. (d) Enter the following menus: Powertrain / Hybrid Control / Data List / Accelerator Position Sensor No. 1 Voltage %, Accelerator
Disassembly
DISASSEMBLY CAUTION / NOTICE / HINT COMPONENTS (DISASSEMBLY)
Procedure Part Name Code
1 REAR DOOR OUTSIDE MOULDING UPPER PAD
75797 -
- -
*1 REAR DOOR OUTSIDE LOWER MOULDING
- -
● Non-reusable part
- - CAUTION / NOTIC
