Toyota Corolla Cross Owners & Service Manuals

Toyota Corolla Cross: Cancellation of 4WD Control (C1299)

DESCRIPTION

While driving, if the heat generated by the transmission coupling assembly exceeds a certain amount or if the estimated oil temperature of the transfer exceeds a certain amount, the 4WD ECU assembly cancels 4WD control and stores DTC C1299.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C1299

Cancellation of 4WD Control

When one of the following conditions is met:

  • Heat generated by transmission coupling assembly exceeds the specified value.
  • Transfer estimated oil temperature exceeds the specified value.
  • Condition, size or tire pressure of the front or rear tires
  • Suspension and ball joint
  • Drive shaft
  • Propeller shaft
  • Transmission coupling assembly
  • 4WD ECU assembly

PROCEDURE

1.

CHECK VEHICLE USAGE

(a) Check that there has been no unintended vehicle usage.

OK:

There is no evidence of rough use (the vehicle has not been driven on damaged or snowy roads, etc. for a long time).

NG

CHECK FOR INTERMITTENT PROBLEMS

OK

2.

CHECK FOR DTC (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)

(a) Check if the electronically controlled brake system DTC is output.

Chassis > Brake/EPB > Trouble Codes

(b) Read the DTCs using the GTS.

Result

Proceed to

Electronically controlled brake system DTCs are not output

A

Electronically controlled brake system DTCs are output

B

B

GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM

A

3.

CHECK RELATED PART

(a) Check the condition, size and tire pressure of the front and rear tires.

Click here

(b) Inspect the suspension and ball joint, etc. for rattle.

(c) Inspect the drive shaft and propeller shaft rotation condition.

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS

OK

4.

RECONFIRM DTC

(a) Clear the DTC.

Chassis > Four Wheel Drive > Clear DTCs

(b) Start the engine.

(c) Drive the vehicle at a speed of 20 km/h (12 mph) or more and check that the same DTC is output.

Chassis > Four Wheel Drive > Trouble Codes

Result

Proceed to

DTC is output

A

DTC is not output

B

B

CHECK FOR INTERMITTENT PROBLEMS

A

5.

REPLACE 4WD ECU ASSEMBLY

Click here

NEXT

6.

RECONFIRM DTC

(a) Clear the DTC.

Chassis > Four Wheel Drive > Clear DTCs

(b) Start the engine.

(c) Drive the vehicle at a speed of 20 km/h (12 mph) or more and check that the same DTC is output.

Chassis > Four Wheel Drive > Trouble Codes

Result

Proceed to

DTC is output

A

DTC is not output

B

A

REPLACE TRANSMISSION COUPLING ASSEMBLY

B

END

    READ NEXT:

     Diameter of the Tire is not Uniform (C1337)

    DESCRIPTION The 4WD ECU assembly outputs DTC C1337 if a difference in tire size is detected. DTC No. Detection Item DTC Detection Condition Trouble Area

     Control Module Communication Bus Off (U0073,U0100,U0126,U0129)

    DESCRIPTION When the signal sent from the 4WD ECU assembly does not finish sending, the 4WD ECU assembly stores a DTC. When a malfunction occurs in communication with the ECM, skid control ECU (br

     AWD Warning Remains ON

    DESCRIPTION The 4WD ECU assembly is connected to the combination meter assembly via the CAN communication system. If the 4WD ECU assembly stores any DTCs which are related to the dynamic torque

    SEE MORE:

     Right Rear Wheel Speed Sensor Circuit Short to Battery (C051212)

    DESCRIPTION Each speed sensor detects wheel speed and sends signals to the skid control ECU (brake actuator assembly). These signals are used by the brake control. The speed sensor detects the magnetic fields of the speed sensor rotor as it rotates and outputs a pulse signal. The frequency

     Diagnostic Trouble Code Chart

    DIAGNOSTIC TROUBLE CODE CHART Lighting System DTC No. Detection Item Link B124400 Light Sensor Circuit Malfunction B241087 Swivel Motor LH Missing Message B241187 Swivel Motor RH Missing Message B241200 Swivel Motor LH Malfunctio

    © 2020-2024 Copyright www.tcorollacross.com