Toyota Corolla Cross: Ultrasonic Sensor (Rear Right Center) Component Internal Failure (C1AE896)
DESCRIPTION
The rear center ultrasonic sensor (RRC sensor) is installed on the rear bumper. The clearance warning ECU assembly detects obstacles based on signals it receives from the rear center ultrasonic sensor (RRC sensor). If an open circuit or other malfunction occurs in the rear center ultrasonic sensor (RRC sensor), the rear center ultrasonic sensor (RRC sensor) does not operate correctly.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
|---|---|---|---|
|
C1AE896 |
Ultrasonic Sensor (Rear Right Center) Component Internal Failure |
Rear center ultrasonic sensor (RRC sensor) failure |
|
CAUTION / NOTICE / HINT
NOTICE:
- Perform registration after replacing or removing and installing the
ultrasonic sensor or clearance warning ECU assembly.
Click here
.gif)
- If a DTC is detected again after the repair, turn the ignition switch to ON and turn the intuitive parking assist system on, and then clear the DTC.
PROCEDURE
|
1. |
CLEAR DTC |
(a) Clear the DTCs.
Body Electrical > Clearance Warning > Clear DTCs
|
.gif)
|
2. |
CHECK FOR DTC |
(a) Check for DTCs.
Body Electrical > Clearance Warning > Trouble Codes|
Result |
Proceed to |
|---|---|
|
DTCs are not output |
A |
|
C1AE896 and C1AE887 are output |
B |
|
C1AE896 is output |
C |
|
None of the above conditions are met |
D |
| A | .gif)
|
USE SIMULATION METHOD TO CHECK |
| B |
|
GO TO DTC (C1AE887)
|
| D |
|
GO TO DTC CHART
|
|
|
3. |
REPLACE REAR CENTER ULTRASONIC SENSOR (RRC SENSOR) |
(a) Replace the rear center ultrasonic sensor (RRC sensor) with a known good one.
HINT:
- Click here
- All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.
|
|
4. |
CLEAR DTC |
(a) Clear the DTCs.
Body Electrical > Clearance Warning > Clear DTCs
|
|
5. |
CHECK FOR DTC |
(a) Check for DTCs.
Body Electrical > Clearance Warning > Trouble Codes|
Result |
Proceed to |
|---|---|
|
DTCs are not output |
A |
|
C1AE896 is output |
B |
|
None of the above conditions are met |
C |
| A |
|
END (REAR CENTER ULTRASONIC SENSOR [RRC SENSOR] WAS DEFECTIVE) |
| B |
|
REPLACE CLEARANCE WARNING ECU ASSEMBLY
|
| C |
|
GO TO DTC CHART
|
READ NEXT:
Ultrasonic Sensor (Rear Right Corner) Missing Message (C1AE987)
DESCRIPTION
This DTC is output when an open circuit or short occurs in the
communication line between a rear corner ultrasonic sensor (RR sensor) and the rear
center ultrasonic sensor (RRC sensor
Ultrasonic Sensor (Rear Right Corner) Component Internal Failure (C1AE996)
DESCRIPTION
The rear corner ultrasonic sensor (RR sensor) is installed on
the rear bumper. The clearance warning ECU assembly detects obstacles based on signals
it receives from the rear corner u
Lost Communication with ECM/PCM "A" Missing Message (U010087,...,U110387)
DESCRIPTION
These DTCs are stored if there is a malfunction in the CAN communication
system connected to the clearance warning ECU assembly.
HINT:
If CAN communication system DTCs are stored, the
SEE MORE:
Installation
INSTALLATION CAUTION / NOTICE / HINT COMPONENTS (INSTALLATION)
Procedure Part Name Code
1 OUTER MIRROR
87961
- - CAUTION / NOTICE / HINT
HINT:
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
Operation Check
OPERATION CHECK CHECK CUSTOMIZE PARAMETERS (a) The operation check below is based on the non-customized initial condition of the vehicle. (However, make sure that "ACC Customize" is set to "ON" using the multi-display.)
Click here CHECK PUSH-BUTTON START FUNCTION
(a) Check the push-button star
