Toyota Corolla Cross: On-vehicle Inspection
ON-VEHICLE INSPECTION
PROCEDURE
1. INSPECT CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY
(a) Check Rotation Direction Signal:
(1) Connect the GTS to the DLC3.
(2) Turn the power switch on (IG).
(3) Turn the GTS on.
(4) Enter the following menus: Powertrain / Engine / Data List / VVT-iE Motor Direction Bank 1.
Powertrain > Engine > Data List|
Tester Display |
|---|
| VVT-iE Motor Direction Bank 1 |
(5) According to the display on the GTS, read the Data List.
Specified Condition:
|
GTS Display | Condition |
Specified Condition |
|---|---|---|
|
VVT-iE Motor Direction Bank 1 |
Power switch off → Power switch on (IG) |
Backward |
HINT:
If the result is not as specified, inspect the cam timing control motor with EDU assembly and wire harness.
(b) Check VVT Change Angle:
(1) Connect the GTS to the DLC3.
(2) Turn the power switch on (IG).
(3) Turn the GTS on.
(4) Put the engine in Inspection Mode (Maintenance Mode).
Powertrain > Hybrid Control > Utility|
Tester Display |
|---|
| Inspection Mode |
(5) Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
(6) Enter the following menus: Powertrain / Engine / Active Test / Control the VVT-iE Opening Angle Bank 1 / Data List / Intake VVT Change Angle Bank 1 and Intake VVT Target Angle Bank 1.
Powertrain > Engine > Active Test|
Active Test Display |
|---|
|
Control the VVT-iE Opening Angle Bank 1 |
|
Data List Display |
|---|
|
Intake VVT Change Angle Bank 1 |
|
Intake VVT Target Angle Bank 1 |
(7) Read the Data List while performing the Active Test with the engine idling.
Specified Condition:
|
Active Test Movement Order |
Difference between "Intake VVT Change Angle Bank 1" and "Intake VVT Target Angle Bank 1" |
|---|---|
|
0 deg → 10 deg → 20 deg → 40 deg → 0 deg → 10 deg → END |
Within 4 DegFR |
HINT:
If the result is not as specified, inspect the cam timing control motor with EDU assembly and camshaft timing gear assembly.
READ NEXT:
Removal
REMOVAL CAUTION / NOTICE / HINT COMPONENTS (REMOVAL)
Procedure Part Name Code
1 ENGINE ASSEMBLY WITH TRANSAXLE
- -
- -
Procedure Pa
Inspection
INSPECTION CAUTION / NOTICE / HINT
NOTICE:
Make sure the contact surface of the cam timing control motor with EDU assembly (the surface that contacts the No. 2 timing chain cover assembly) is fr
Installation
INSTALLATION CAUTION / NOTICE / HINT COMPONENTS (INSTALLATION)
Procedure Part Name Code
1 CAM TIMING CONTROL MOTOR O-RING
13090E
- -
SEE MORE:
Manifold Absolute Pressure / Barometric Pressure Sensor Circuit Short to Battery or Open (P010515)
DESCRIPTION Refer to DTC P010511. Click here
DTC No. Detection Item
DTC Detection Condition Trouble Area
MIL Note
P010515 Manifold Absolute Pressure / Barometric Pressure Sensor Circuit Short to Battery or Open
The E.F.I. vacuum sensor assembly output voltag
Motor Electronics Coolant Pump "A" Component Internal Failure (P0C7396)
DTC SUMMARY MALFUNCTION DESCRIPTION This DTC is stored when the inverter water pump assembly is malfunctioning. The cause of this malfunction may be one of the following: Inverter water pump assembly malfunction
Inverter water pump assembly internal malfunction
Open or short in wire harn
