Toyota Corolla Cross: Insufficient Coolant Temperature for Closed Loop Fuel Control (P012500)

DESCRIPTION

Refer to DTC P011511.

Click here

MONITOR DESCRIPTION

The resistance of the engine coolant temperature sensor varies in proportion to the actual engine coolant temperature. The ECM supplies a constant voltage to the sensor and monitors the signal output voltage of the sensor. The signal output voltage varies according to the changing resistance of the sensor. After the engine is started, the engine coolant temperature is monitored by this signal. If the engine coolant temperature sensor indicates that the engine is not yet warm enough for closed loop fuel control, despite a specified period of time having elapsed since the engine was started, the ECM interprets this as a malfunction in the sensor or engine cooling system, illuminates the MIL and stores this DTC.

MONITOR STRATEGY

TYPICAL ENABLING CONDITIONS

TYPICAL MALFUNCTION THRESHOLDS

CONFIRMATION DRIVING PATTERN

HINT:

• After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

  Click here

• When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.

  Click here

1. Leave the vehicle outside overnight.
2. Connect the GTS to the DLC3.
3. Turn the ignition switch to ON.
4. Turn the GTS on.
5. Enter the following menus: Powertrain / Engine / Trouble Codes.
6. Read the DTC and record the Freeze Frame Data.
7. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
8. Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature.
9. Check that Coolant Temperature is the same or less than Initial Engine Coolant Temperature in the Freeze Frame Data.
10. Turn the ignition switch off and wait for at least 30 seconds.
11. Start the engine [A].
12. Turn the GTS on.
13. Wait 21 minutes or more [B].
14. Enter the following menus: Powertrain / Engine / Trouble Codes [C].
15. Read the pending DTCs.

    HINT:

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
16. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
17. Input the DTC: P012500.
18. Check the DTC judgment result.

    GTS Display	Description
    NORMAL	DTC judgment completed System normal
    ABNORMAL	DTC judgment completed System abnormal
    INCOMPLETE	DTC judgment not completed Perform driving pattern after confirming DTC enabling conditions

    HINT:

    • If the judgment result is NORMAL, the system is normal.
    • If the judgment result is ABNORMAL, the system is malfunctioning.
    • If the judgment result is INCOMPLETE, let the engine cool down (engine coolant temperature is below 5°C (41°F)), and then perform steps [A] and [C]: Normal judgment procedure.

      The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.

    • When clearing the permanent DTCs, do not disconnect the cable from the auxiliary battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.

WIRING DIAGRAM

Refer to DTC P011511.

Click here

CAUTION / NOTICE / HINT

HINT:

• If any of DTCs P011511, P011515 or P01152A are output simultaneously with DTC P012500, the engine coolant temperature sensor may have an open or a short circuit. Troubleshoot those DTCs first.
• Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

(a) Read the DTCs.

HINT:

If any DTCs other than P012500 are output, troubleshoot those DTCs first.

B

GO TO DTC CHART

A

(a) Inspect the water inlet with thermostat sub-assembly (thermostat opening temperature).

Click here

NG

REPLACE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

OK

(a) Check for defects in the engine cooling system that might cause the system to be too cold, such as abnormal cooling fan operation or any modifications.

HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click here

OK

REPLACE ENGINE COOLANT TEMPERATURE SENSOR

NG

REPAIR OR REPLACE ENGINE COOLING SYSTEM

READ NEXT: