Toyota Corolla Cross Owners & Service Manuals

Toyota Corolla Cross: How To Proceed With Troubleshooting

CAUTION / NOTICE / HINT

HINT:

  • Use the following procedure to troubleshoot the seat belt warning system.
  • *: Use the GTS.

PROCEDURE

1.

VEHICLE BROUGHT TO WORKSHOP

NEXT

2.

CUSTOMER PROBLEM ANALYSIS

(a) Interview the customer to confirm the problem.

Click here

NEXT

3.

PRE-CHECK

(a) Measure the auxiliary battery voltage.

Standard Voltage:

11 to 14 V

If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.

(b) Check the fuses and relays.

(c) Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.

NEXT

4.

CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

(a) Using the GTS, check for CAN communication system DTCs.

  • for HEV Model:

    Click here

  • for Gasoline Model:

    Click here

Result

Proceed to

CAN DTCs are not output

A

CAN DTCs are output

B

B

GO TO CAN COMMUNICATION SYSTEM

for HEV Model: Click here

for Gasoline Model: Click here

A

5.

CHECK COMMUNICATION FUNCTION OF CXPI COMMUNICATION SYSTEM*

(a) Using the GTS, check for CXPI communication system DTCs.

Body Electrical > Main Body > Trouble Codes

Result

Proceed to

CXPI communication system DTCs are not output

A

CXPI communication system DTCs are output

B

B

GO TO CXPI COMMUNICATION SYSTEM

A

6.

CHECK DTC OUTPUT (AIRBAG SYSTEM)*

(a) Clear the DTCs.

Body Electrical > SRS Airbag > Clear DTCs

(b) Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes

Result

Proceed to

DTCs are not output

A

DTCs are output

B

B

GO TO AIRBAG SYSTEM

A

7.

CHECK COMBINATION METER ASSEMBLY

(a) Check the operation of the speedometer, shift indicator and brake warning light on the combination meter assembly.

OK:

The speedometer, shift indicator* and brake warning light on the combination meter assembly operate normally.

NG

GO TO METER / GAUGE SYSTEM

OK

8.

PROBLEM SYMPTOMS TABLE

(a) Refer to Problem Symptoms Table.

Click here

Result

Proceed to

Fault is not listed in Problem Symptoms Table

A

Fault is listed in Problem Symptoms Table

B

B

GO TO STEP 10

A

9.

OVERALL ANALYSIS AND TROUBLESHOOTING*

(a) Data List / Active Test

Click here

(b) Terminals of ECU

Click here

(c) On-vehicle Inspection

Click here

NEXT

10.

REPAIR OR REPLACE

NEXT

11.

CONFIRMATION TEST

NEXT

END

    READ NEXT:

     Customize Parameters

    CUSTOMIZE PARAMETERS NOTICE: When the customer requests a change in a function, first make sure that the function can be customized. Be sure to make a note of the current settings before cu

     Problem Symptoms Table

    PROBLEM SYMPTOMS TABLE NOTICE: When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the info

     Terminals Of Ecu

    TERMINALS OF ECU CHECK POWER DISTRIBUTION BOX ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (a) Remove the main body ECU (multiplex network body ECU). Click here *1 Power

    SEE MORE:

     Disassembly

    DISASSEMBLY CAUTION / NOTICE / HINT COMPONENTS (DISASSEMBLY) Procedure Part Name Code 1 BRAKE MASTER CYLINDER STRAIGHT PIN - - - 2 BRAKE MASTER C

     There is No Sound Made

    DESCRIPTION Based on signals received from each ECU, the vehicle approaching speaker controller outputs warning sounds through the vehicle approaching speaker assembly. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: Inspect the fuses for circuits related to this system before performing the fol

    © 2020-2024 Copyright www.tcorollacross.com