Toyota Corolla Cross: Data List / Active Test
DATA LIST / ACTIVE TEST
DATA LIST
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
(a) Read the Data List according to the display on the GTS.
Body Electrical > Main Body > Data List|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Communication D-Door Motor |
Connection status between power window regulator motor assembly (driver door) and main body ECU (multiplex network body ECU) |
OK or STOP |
OK: Connected STOP: Not Connected |
DTC is output if an error occurs in LIN communication. |
|
Communication P-Door Motor |
Connection status between power window regulator motor assembly (front passenger door) and main body ECU (multiplex network body ECU) |
OK or STOP |
OK: Connected STOP: Not Connected |
DTC is output if an error occurs in LIN communication. |
|
Communication RR-Door Motor |
Connection status between power window regulator motor assembly (rear door RH) and main body ECU (multiplex network body ECU) |
OK or STOP |
OK: Connected STOP: Not Connected |
DTC is output if an error occurs in LIN communication. |
|
Communication RL-Door Motor |
Connection status between power window regulator motor assembly (rear door LH) and main body ECU (multiplex network body ECU) |
OK or STOP |
OK: Connected STOP: Not Connected |
DTC is output if an error occurs in LIN communication. |
|
Communication Sunshade ECU |
Connection status between roof sunshade ECU (sliding roof drive gear assembly) and main body ECU (multiplex network body ECU) |
STOP or OK |
STOP: Not Connected OK: Connected |
|
|
Communication Slide Roof |
Connection status between main body ECU (multiplex network body ECU) and sliding roof ECU (sliding roof drive gear sub-assembly) |
OK or STOP |
OK: Connected STOP: Not Connected |
|
|
Communication Double Locking |
Connection status between double lock door control relay assembly and main body ECU (multiplex network body ECU) |
STOP or OK |
STOP: Not Connected OK: Connected |
|
|
Communication Master Switch |
Connection status between multiplex network master switch assembly and main body ECU (multiplex network body ECU) |
OK or STOP |
OK: Connected STOP: Not Connected |
DTC is output if an error occurs in LIN communication. |
READ NEXT:
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART
LIN Communication System
DTC No.
Detection Item
Link
B120687
P/W Master SW System Missing Message
P/W Master SW System Missing Message (B120687,B127387,B232187-B232487)
DESCRIPTION
This DTC is stored when LIN communication between the main body ECU (multiplex
network body ECU) and multiplex network master switch assembly, front power window
regulator motor assem
LIN Communication Missing Message (B228787)
DESCRIPTION
When an internal malfunction is detected in the certification ECU (smart key
ECU assembly), this DTC is stored.
DTC No.
Detection Item
DTC Detection Co
SEE MORE:
Installation
INSTALLATION
CAUTION / NOTICE / HINT
COMPONENTS (INSTALLATION)
Procedure
Part Name Code
1
DIFFERENTIAL DYNAMIC DAMPER
41196B
-
-
-
2
REAR TRACTION
Inspection
INSPECTION PROCEDURE 1. INSPECT CYLINDER HEAD SUB-ASSEMBLY
(a) Using a precision straightedge and feeler gauge, measure the warpage of the contact surfaces where the cylinder head sub-assembly contacts the cylinder block sub-assembly, intake manifold and exhaust manifold.
*a Bottom Si
