Toyota Corolla Cross Owners & Service Manuals

Toyota Corolla Cross: Stopping the engine

1. Stop the vehicle completely.

2. Set the parking brake, and shift the shift lever to P.

Check the parking brake indicator is illuminated.

Do not press the shift lever button after shifting the shit position to P.

3. Press the engine switch.

The engine will stop, and the meter display will be extinguished.

4. Release the brake pedal and check that "ACCESSORY" or "IGNITION ON" is not shown on the multi-information display.

■Automatic engine shut off feature

  • The vehicle is equipped with a feature that automatically shuts off the engine when the shift lever is in P with the engine running for an extended period.
  • The engine will automatically shut off after approximately 1 hour if it has been left running while the shift lever is in P.
  • The timer for the automatic engine shut off feature will reset if the brake pedal is depressed or if the shift lever is in a position other than P.
  • After the vehicle is parked, if the door is locked with the door lock switch from the inside or the mechanical key from the outside, the automatic engine shut off feature will be disabled.

    The timer for the automatic engine shut off feature will be re-enabled if the driver's door is opened.

WARNING

■Stopping the engine in an emergency

  • If you want to stop the engine in an emergency while driving the vehicle, press and hold the engine switch for more than 2 seconds, or press it briefly 3 times or more in succession.

    However, do not touch the engine switch while driving except in an emergency. Turning the engine off while driving will not cause loss of steering or braking control, but the power assist to these systems will be lost. This will make it more difficult to steer and brake, so you should pull over and stop the vehicle as soon as it is safe to do so.

  • If the engine switch is operated while the vehicle is running, a warning message will be shown on the multi-information display and a buzzer sounds.
  • To restart the engine after performing an emergency shutdown, shift the shift lever to N and then press the engine switch.

■When parking

Exhaust gases include harmful carbon monoxide (CO), which is colorless and odorless. Observe the following precautions.

Failure to do so may cause exhaust gases to enter the vehicle and may lead to an accident caused by light-headedness, or may lead to death or a serious health hazard.

  • If the vehicle is in a poorly ventilated area or a closed area, such as a garage, stop the engine.
  • Do not leave the vehicle with the engine running for a long time. If such a situation cannot be avoided, park the vehicle in an open space and ensure that exhaust fumes do not enter the vehicle interior.
  • Do not leave the engine running in an area with snow build-up, or where it is snowing. If snowbanks build up around the vehicle while the engine is running, exhaust gases may collect and enter the vehicle.

    READ NEXT:

     Changing engine switch modes

    Modes can be changed by pressing the engine switch with brake pedal released. (The mode changes each time the switch is pressed.) OFF*1 The emergency flashers can be used. ACC*2 Some electrical

     Continuously variable transmission

    Select the shift position depending on your purpose and situation. Shift position purpose and functions P - Parking the vehicle/ starting the engine R - Reversing N - Neutral (Condition in which the p

     Turn signal lever

    Operating instructions Right turn Lane change to the right (move the lever partway and release it) The right hand signals will flash 3 times. Lane change to the left (move the lever partway

    SEE MORE:

     Terminals Of Ecu

    TERMINALS OF ECU CLEARANCE WARNING ECU ASSEMBLY (a) Disconnect the I24 clearance warning ECU assembly connector. (b) Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below. Terminal No. (Symbol) Terminal Descri

     Removal

    REMOVAL CAUTION / NOTICE / HINT COMPONENTS (REMOVAL) Procedure Part Name Code 1 INTAKE MANIFOLD 17111 - - - 2 KNOCK CONTROL SENSOR 89615 - - CAUTION / NOTICE / HINT The necessary procedures (adjustment, cali

    © 2020-2024 Copyright www.tcorollacross.com