Toyota Corolla Cross: Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
HINT:
- Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
- Inspect the fuses and relays related to this system before inspecting the suspected areas below.
|
Symptom | Suspected Area |
Link |
|---|---|---|
|
Engine does not crank (Does not start) |
Flow chart [Engine difficult to start] |
|
|
Flow chart [Engine difficult to start] (Vehicle Control History Code: X0810, X0811 and/or X0812) |
| |
|
Auxiliary battery |
| |
|
ST relay |
| |
|
Starter assembly |
| |
|
Starter signal circuit |
| |
|
Smart key system (for start function) (w/ Smart Key System) |
| |
|
VC output circuit (ECM 5 V output) |
| |
|
Park/Neutral position switch assembly (for 2WD) |
| |
|
Park/Neutral position switch assembly (for AWD) |
| |
|
No initial combustion (Does not start) |
Immobiliser system (w/ Smart Key System) |
|
|
Immobiliser system (w/o Smart Key System) |
| |
|
ECM power source circuit |
| |
|
VC output circuit (ECM 5 V output) |
| |
|
Flow chart [Engine difficult to start] |
| |
|
Flow chart [Engine difficult to start] (Vehicle Control History Code: X0810, X0811 and/or X0812) |
| |
|
Ignition system |
| |
|
Fuel system |
| |
|
Port fuel injector assembly |
| |
|
Direct fuel injector assembly |
| |
|
Crankshaft position sensor |
| |
|
Intake system |
| |
|
Valve timing |
| |
|
EGR valve assembly |
| |
|
No. 1 valve rocker arm sub-assembly* |
| |
|
Engine cranks normally but difficult to start |
ECM power source circuit |
|
|
Flow chart [Engine difficult to start] |
| |
|
Flow chart [Engine difficult to start] (Vehicle Control History Code: X0810, X0811 and/or X0812) |
| |
|
Throttle body with motor assembly |
| |
|
Fuel pump assembly (for high pressure side) |
| |
|
Fuel pump (for low pressure side) (for 2WD) |
| |
|
Fuel pump (for low pressure side) (for AWD) |
| |
|
Engine coolant temperature sensor |
| |
|
Fuel system |
| |
|
Ignition system |
| |
|
Spark plug |
| |
|
Compression |
| |
|
Port fuel injector assembly |
| |
|
Direct fuel injector assembly |
| |
|
Crankshaft position sensor |
| |
|
Intake system |
| |
|
Valve timing |
| |
|
EGR valve assembly |
| |
|
No. 1 valve rocker arm sub-assembly* |
| |
|
Incomplete intermittent combustion occurs (Does not start) |
Flow chart [Engine difficult to start] |
|
|
Flow chart [Engine difficult to start] (Vehicle Control History Code: X0810, X0811 and/or X0812) |
| |
|
Fuel system |
| |
|
Ignition system |
| |
|
Port fuel injector assembly |
| |
|
Direct fuel injector assembly |
| |
|
Crankshaft position sensor |
| |
|
Intake system |
| |
|
Valve timing |
| |
|
High engine speed | Throttle body with motor assembly |
|
|
ECM power source circuit |
| |
|
PCV system |
| |
|
Low engine speed (Poor idle) |
Flow chart [Rough idling] |
|
|
Flow chart [Rough idling] (Vehicle Control History Code: X0821, X0822, X0823, X0824, X082A, X082D and/or X082E) |
| |
|
Fuel system |
| |
|
Throttle body with motor assembly |
| |
|
Port fuel injector assembly |
| |
|
Direct fuel injector assembly |
| |
|
Fuel pump assembly (for high pressure side) |
| |
|
PCV system |
| |
|
Intake system |
| |
|
Rough idle | Flow chart [Rough idling] |
|
|
Flow chart [Rough idling] (Vehicle Control History Code: X0821, X0822, X0823, X0824, X082A, X082D and/or X082E) |
| |
|
Throttle body with motor assembly |
| |
|
Port fuel injector assembly |
| |
|
Direct fuel injector assembly |
| |
|
Fuel pump assembly (for high pressure side) |
| |
|
Ignition system |
| |
|
Air fuel ratio sensor (sensor 1) |
| |
|
Air fuel ratio sensor (sensor 2) |
| |
|
Mass air flow meter sub-assembly |
| |
|
Manifold absolute pressure sensor |
| |
|
Compression |
| |
|
Fuel system |
| |
|
Spark plug |
| |
|
Intake system |
| |
|
Valve timing |
| |
|
EGR valve assembly |
| |
|
No. 1 valve rocker arm sub-assembly* |
| |
|
Hunting (Poor idle) | Throttle body with motor assembly |
|
|
ECM power source circuit |
| |
|
Flow chart [Rough idling] |
| |
|
Flow chart [Rough idling] (Vehicle Control History Code: X0821, X0822, X0823, X0824, X082A, X082D and/or X082E) |
| |
|
Fuel system |
| |
|
Spark plug |
| |
|
Intake system |
| |
|
Drive start control |
| |
|
Hesitation/Poor acceleration (Poor driveability) |
Flow chart [Rough idling] |
|
|
Flow chart [Rough idling] (Vehicle Control History Code: X0821, X0822, X0823, X0824, X082A, X082D and/or X082E) |
| |
|
Port fuel injector assembly |
| |
|
Direct fuel injector assembly |
| |
|
Fuel system |
| |
|
Fuel pump assembly (for high pressure side) |
| |
|
Ignition system |
| |
|
Spark plug |
| |
|
Intake system |
| |
|
Valve timing |
| |
|
No. 1 valve rocker arm sub-assembly* |
| |
|
Brake override system |
| |
|
Drive start control |
| |
|
Lack of power | Flow chart [Lack of power] |
|
|
Flow chart [Lack of power] (Vehicle Control History Code: X0844 and/or X0845) |
| |
|
Surging (Poor driveability) |
Flow chart [Rough idling] |
|
|
Flow chart [Rough idling] (Vehicle Control History Code: X0821, X0822, X0823, X0824, X082A, X082D and/or X082E) |
| |
|
Fuel system |
| |
|
Spark plug |
| |
|
Port fuel injector assembly |
| |
|
Direct fuel injector assembly |
| |
|
No. 1 valve rocker arm sub-assembly* |
| |
|
Engine stalls soon after starting |
Flow chart [Engine stalls] |
|
|
Flow chart [Engine stalls] (Vehicle Control History Code: X0800 and/or X0803) |
| |
|
Fuel system |
| |
|
Throttle body with motor assembly |
| |
|
Crankshaft position sensor |
| |
|
Ignition system |
| |
|
Fuel pump assembly (for high pressure side) |
| |
|
Intake system |
| |
|
Valve timing |
| |
|
EGR valve assembly |
| |
|
Engine stalls soon after slow down |
Flow chart [Engine stalls] |
|
|
Flow chart [Engine stalls] (Vehicle Control History Code: X0800 and/or X0803) |
| |
|
Port fuel injector assembly |
| |
|
Direct fuel injector assembly |
| |
|
Throttle body with motor assembly |
| |
|
ECM |
| |
|
Crankshaft position sensor |
| |
|
Ignition system |
| |
|
MIL (Malfunction Indicator Lamp) malfunction |
MIL Circuit |
|
|
Meter/Gauge system |
| |
|
Unable/difficult to refuel |
Fuel system (canister, refueling valve, roll over valve, fuel tank, etc.) |
- |
HINT:
*: Check "Fuel Cut Elapsed Time" in the Data List. If the elapsed time is over 0 sec, then the engine speed is high (the engine speed at which fuel cut occurs + 500 rpm or more). In this situation, there is a possibility that a No. 1 valve rocker arm sub-assembly will become loose and malfunction, check that the No. 1 valve rocker arm sub-assemblies are properly installed.
Click here .gif)
READ NEXT:
Diagnosis System
DIAGNOSIS SYSTEM OBD II (except Mexico Models)
When troubleshooting OBD II (On-Board Diagnostics) vehicles, the GTS (complying with SAE J1978) must be connected to the DLC3 (Data Link Connector 3)
Dtc Check / Clear
DTC CHECK / CLEAR NOTICE: When the diagnosis system is changed from normal mode to check mode or vice versa, all DTCs and Freeze Frame Data recorded in normal mode are cleared. Before changing modes,
Freeze Frame Data
FREEZE FRAME DATA DESCRIPTION The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can be helpful in deter
SEE MORE:
Installation
INSTALLATION CAUTION / NOTICE / HINT COMPONENTS (INSTALLATION)
Procedure Part Name Code
1 ACCELERATOR PEDAL SENSOR ASSEMBLY
78110K
- -
2 FRONT NO. 1 CONSOLE BOX INSERT
58816D -
- -
3 NO. 1 INSTRUMENT PA
On-vehicle Inspection
ON-VEHICLE INSPECTION
PROCEDURE
1. INSPECT RADIO SETTING CONDENSER
(a) With the radio setting condenser installed, check that there is
no looseness or other abnormalities.
(b) Measure the resistance of the radio setting condenser
according to the value(s) in the table below.
