Toyota Corolla Cross Owners & Service Manuals

Toyota Corolla Cross: Operation Check

OPERATION CHECK

INSPECT ILLUMINATED ENTRY SYSTEM OPERATION

NOTICE:

Perform this inspection with the customize parameters at the initial settings.

Click here

HINT:

Perform this inspection with the map light assembly door linked switch on and the room light assembly switch set to DOOR.

Control

Condition

Lights that Operate

Actuation Area-linked*1

With the push start switch off and all of the doors closed and locked, enter an exterior detection area while carrying an electrical key transmitter and check that the lights that operate turn on for approximately 15 seconds and then turn off.

  • Map light assembly
  • No. 1 room light assembly
  • Front Door Ambient Illumination Light (Front Door Trim Board Sub-assembly)*3
  • Center tray illumination light (No. 1 interior illumination light assembly)*3

Door Lock/Unlock-linked

With the ignition switch off and all of the doors closed and locked, unlock any door using an unlock operation (key-linked, wireless or entry unlock operation) and check that the lights that operate turn on for 15 seconds and then turn off.

  • Map light assembly
  • No. 1 room light assembly
  • Front Door Ambient Illumination Light (Front Door Trim Board Sub-assembly)*3
  • Center tray illumination light (No. 1 interior illumination light assembly)*3

Door Open/Close-linked

With the ignition switch off and all of the doors closed, open any door and check that the lights that operate turn on. While the lights that operate are on, close all of the doors and check that the lights that operate turn off after approximately 15 seconds.

  • Map light assembly
  • No. 1 room light assembly
  • Front Door Ambient Illumination Light (Front Door Trim Board Sub-assembly)*3
  • Center tray illumination light (No. 1 interior illumination light assembly)*3

With the push start switch off and all of the doors closed, open any front door and check that the light that operates turns on. While the light that operates is on, close the front doors and check that the light that operates turns off after approximately 40 seconds.

Push Start Switch Illumination*1

With the ignition switch in ON, open any door and check that the lights that operate turn on. While the lights that operate are on, close all of the doors and check that the lights that operate turn off.

  • Map light assembly
  • No. 1 room light assembly

Push Start Switch Illumination*1

Turn the ignition switch from ACC or ON to off and check that the lights that operate turn on for approximately 15 seconds and then turn off.

  • Map light assembly
  • No. 1 room light assembly
  • Front Door Ambient Illumination Light (Front Door Trim Board Sub-assembly)*3
  • Center tray illumination light (No. 1 interior illumination light assembly)*3

Turn the ignition switch from ACC or ON to off and check that the light that operates turns on for approximately 40 seconds and then turns off.

Push Start Switch Illumination

Push Start Switch-linked*1

Turn the ignition switch from ACC or ON to off and check that the lights that operate turn on for approximately 15 seconds and then turn off.

  • Map light assembly
  • No. 1 room light assembly
  • Front Door Ambient Illumination Light (Front Door Trim Board Sub-assembly)*3
  • Center tray illumination light (No. 1 interior illumination light assembly)*3

Turn the ignition switch from ACC or ON to off and check that the light that operates turns on for approximately 40 seconds and then turns off.

Push Start Switch Illumination*1

Ignition Switch-linked*2

Turn the ignition switch from ACC or ON to off and check that the lights that operate turn on for approximately 15 seconds and then turn off.

  • Map light assembly
  • No. 1 room light assembly
  • *1: w/ Smart Key System
  • *2: w/o Smart Key System
  • *3: w/ Ambient Illumination Light

INSPECT AUXILIARY BATTERY SAVING CONTROL OPERATION

(a) The operations and conditions of this control are described below.

Control

Condition

Lights that Operate

Basic Operation

When 20 minutes elapse after the ignition switch is turned from ACC or ON to off and the lights that operate remain on, the lights are turned off.

HINT:

Battery saving control is canceled when any of the following operations is performed before the lights are turned off by battery saving control. After the operation is performed, the lights remain on for another 20 minutes and then the lights are turned off.

  • The ignition switch is ACC or ON.
  • Any door is opened and closed.
  • Any door is unlocked.
  • The key enters any exterior actuation area.*1
  • Map light assembly
  • No. 1 room light assembly
  • No. 1 Luggage Compartment Light Assembly
  • Front Door Ambient Illumination Light (Front Door Trim Board Sub-assembly)*2
  • Center tray illumination light (No. 1 interior illumination light assembly)*2
  • Vanity Light Assembly*3

When 20 minutes elapse after the driver door/front passenger door is opened and the lights that operate remain on, the lights are turned off.

HINT:

Battery saving control is canceled when any of the following operations is performed before the lights are turned off by battery saving control. After the operation is performed, the lights remain on for another 20 minutes and then the lights are turned off.

  • Any front door is opened and closed.

Push Start Switch Illumination*1

  • *1: w/ Smart Key System
  • *2: w/ Ambient Illumination Light
  • *3: w/ Vanity Light

    READ NEXT:

     Customize Parameters

    CUSTOMIZE PARAMETERS CUSTOMIZE LIGHTING SYSTEM (INT) NOTICE: When the customer requests a change in a function, first make sure that the function can be customized. Be sure to make a note o

     Problem Symptoms Table

    PROBLEM SYMPTOMS TABLE NOTICE: Before replacing the main body ECU (multiplex network body ECU) or certification ECU (smart key ECU assembly)*1, refer to Registration. *1: w/ Smart Key Syst

     Terminals Of Ecu

    TERMINALS OF ECU CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND POWER DISTRIBUTION BOX ASSEMBLY (a) Remove the main body ECU (multiplex network body ECU) from the power distribution box assem

    SEE MORE:

     Removal

    REMOVAL CAUTION / NOTICE / HINT COMPONENTS (REMOVAL) Procedure Part Name Code 1 BRAKE MASTER CYLINDER SUB-ASSEMBLY 47201 - - - 2 VACUUM SENSOR ASSEMBLY 89420H - - - 3 VACUUM SENSOR GROMMET - - -

     Main Microcomputer in Front Radar Sensor System Internal Failure (C1A8C04,C1A8C46,C1A8D1C,C1A9000)

    DESCRIPTION When an internal malfunction is detected in the millimeter wave radar sensor assembly, a DTC is stored. DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from C1A8C04 Main Microcom

    © 2020-2024 Copyright www.tcorollacross.com