Toyota Corolla Cross: Motor Electronics Coolant Temperature Sensor Circuit Short to Ground (P0A0011,P0A0015)
DESCRIPTION
Refer to the description for DTC P0A001C.
Click here .gif)
|
DTC No. | Detection Item |
DTC Detection Condition |
Trouble Area | MIL |
Warning Indicate | Note |
|---|---|---|---|---|---|---|
|
P0A0011 | Motor Electronics Coolant Temperature Sensor Circuit Short to Ground |
Short to ground detected in HV coolant temperature sensor circuit (1 trip detection logic) |
Inverter with converter assembly |
Comes on | Master Warning: Comes on | SAE Code: P0A02 |
| P0A0015 |
Motor Electronics Coolant Temperature Sensor Circuit Short to Battery or Open |
Open or short to +B detected in HV coolant temperature sensor circuit (1 trip detection logic) |
Inverter with converter assembly |
Comes on | Master Warning: Comes on | SAE Code: P0A03 |
MONITOR DESCRIPTION
If the motor generator control ECU detects a malfunction in the HV coolant temperature sensor it will illuminate the MIL and store a DTC.
MONITOR STRATEGY
|
Related DTCs | P0A02 (INF P0A0011): Motor Electronics Coolant Temperature Sensor Range check (Low voltage) P0A03 (INF P0A0015): Motor Electronics Coolant Temperature Sensor Range check (High voltage) |
|
Required sensors/components | HV coolant temperature sensor |
|
Frequency of operation | Continuous |
|
Duration | TMC's intellectual property |
|
MIL operation | Immediately |
|
Sequence of operation | None |
TYPICAL ENABLING CONDITIONS
|
The monitor will run whenever the following DTCs are not stored |
TMC's intellectual property |
|
Other conditions belong to TMC's intellectual property |
- |
TYPICAL MALFUNCTION THRESHOLDS
|
TMC's intellectual property |
- |
COMPONENT OPERATING RANGE
|
Motor generator control ECU | DTC P0A02 (INF P0A0011) is not detected DTC P0A03 (INF P0A0015) is not detected |
CONFIRMATION DRIVING PATTERN
HINT:
- After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
- When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the ignition switch off and wait for 2 minutes or more.
- Turn the ignition switch to ON and wait for 5 seconds or more. [*1]
HINT:
[*1]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.
- Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE, perform the normal judgment procedure again.
CAUTION / NOTICE / HINT
HINT:
After the repair, clear the DTCs. If the value of Data List item "Inverter Coolant Temperature" is not abnormal (110°C (230°F) or -40°C (-40°F)) when the ignition switch is turned to ON, the condition is judged as normal.
(If DTC P0A0011 is output, 110°C (230°F) will be displayed and if DTC P0A0015 is output, -40°C (-40°F) will be displayed.)
PROCEDURE
|
1. | REPLACE INVERTER WITH CONVERTER ASSEMBLY |
Click here
| NEXT | .gif) | COMPLETED |
READ NEXT:
Motor Electronics Coolant Temperature Sensor Circuit Voltage Out of Range (P0A001C)
DTC SUMMARY MALFUNCTION DESCRIPTION These DTCs indicate that the temperature sensor value is abnormal. The cause of this malfunction may be one of the following:
Area Main Malfunction Descrip
Generator Control Module Circuit Intermittent (P0A1B1F)
DESCRIPTION If the motor generator control ECU, which is built into the inverter with converter assembly, is reset due to a problem with the power source in the inverter, the motor generator control E
Drive Motor "A" Control Module Unexpected Operation (P0A1B94)
DTC SUMMARY MALFUNCTION DESCRIPTION For the calculation processing (in particular, calculation processing related to driving force such as torque calculations and inverter control) that takes place in
SEE MORE:
Removal
REMOVAL CAUTION / NOTICE / HINT COMPONENTS (REMOVAL)
Procedure Part Name Code
1 CUT KEY
69503B
- -
2 TRANSMITTER HOUSING COVER
-
- -
3 TRANSMITTER BATTERY
89745C
- -
Installation
INSTALLATION CAUTION / NOTICE / HINT COMPONENTS (INSTALLATION)
Procedure Part Name Code
1 OUTER MIRROR
87961
- - CAUTION / NOTICE / HINT
HINT:
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
