Toyota Corolla Cross: Left Front Wheel Speed Sensor Signal Stuck High (C050024)
DESCRIPTION
Refer to DTC C050012
Click here .gif)
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
DTC Output from |
Note |
|---|---|---|---|---|---|---|
|
C050024 |
Left Front Wheel Speed Sensor Signal Stuck High |
The speed sensor signal is not within the specified range for 5 seconds or more. |
Front speed sensor LH |
Comes on |
Brake/EPB |
|
MONITOR DESCRIPTION
If the output signal from the speed sensor exceeds the possible output range, the skid control ECU (brake actuator assembly) illuminates the MIL and stores this DTC.
MONITOR STRATEGY
|
Related DTCs |
C0501 (Case 1): Wheel speed sensor range monitoring (FL) |
|
Required Sensors/Components(Main) |
Speed sensor |
|
Required Sensors/Components(Related) |
Skid control ECU (brake actuator assembly) |
|
Frequency of Operation |
Continuous |
|
Duration |
5 seconds |
|
MIL Operation |
2 driving cycles |
|
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
|
Monitor runs whenever the following DTCs are not stored |
TMC's intellectual property |
|
Other conditions belong to TMC's intellectual property |
- |
TYPICAL MALFUNCTION THRESHOLDS
|
TMC's intellectual property |
- |
COMPONENT OPERATING RANGE
|
TMC's intellectual property |
- |
CONFIRMATION DRIVING PATTERN
NOTICE:
When performing the normal judgment procedure, make sure that the driver door is closed and is not opened at any time during the procedure.
HINT:
- After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
- When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
- Connect the GTS to the DLC3.
- Turn the ignition switch to ON and turn the GTS on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the ignition switch off.
- Turn the ignition switch to ON (READY) and turn the GTS on.
- Wait for 5 seconds or more. [*]
HINT:
[*]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- Enter the following menus: Chassis / Brake/EPB* / Utility / All Readiness.
*: Electric Parking Brake System
- Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE, perform driving pattern again.
PROCEDURE
|
1. |
REPLACE FRONT SPEED SENSOR LH |
Click here
| NEXT | .gif)
|
END |
READ NEXT:
Left Front Wheel Speed Sensor Internal Electronic Failure (C050049)
DESCRIPTION
When the system is starting up and the skid control ECU (brake
actuator assembly) detects a speed sensor circuit malfunction via the speed sensor
circuit self-diagnosis function, this
Right Front Wheel Speed Sensor Circuit Short to Battery (C050612)
DESCRIPTION
Each speed sensor detects wheel speed and sends signals to the
skid control ECU (brake actuator assembly). These signals are used by the brake
control.
The speed sensor detects the m
Right Front Wheel Speed Sensor Circuit Short to Ground or Open (C050614)
DESCRIPTION
Refer to DTC C050612
Click here
DTC No.
Detection Item
DTC Detection Condition
Trouble Area
MIL
DTC Output from
SEE MORE:
Ultrasonic Sensor (Rear Right Corner) Component Internal Failure (C1AE996)
DESCRIPTION
The rear corner ultrasonic sensor (RR sensor) is installed on
the rear bumper. The clearance warning ECU assembly detects obstacles based on signals
it receives from the rear corner ultrasonic sensor (RR sensor). If an open circuit
or other malfunction occurs in the rear corner ul
Camera Axis Adjustment Value Write
CAMERA AXIS ADJUSTMENT VALUE WRITE
CAUTION / NOTICE / HINT
NOTICE:
When replacing the forward recognition camera or millimeter wave radar
sensor assembly, always replace them with new ones. If they are replaced
with used parts or parts from another vehicle, then an incorrect FOE is
