Toyota Corolla Cross: Installation
INSTALLATION
CAUTION / NOTICE / HINT
COMPONENTS (INSTALLATION)
|
Procedure | Part Name Code |
.png) |
.png) |
.png) | |
|---|---|---|---|---|---|
|
1 | FRONT SEAT INNER BELT ASSEMBLY |
73230 |
|
- | - |
|
2 | SEPARATE TYPE FRONT SEATBACK COVER |
71073S | - |
- | - |
|
3 | FRONT SEAT ASSEMBLY |
- |
|
- | - |
.gif)
|
*A | for Driver Side Manual Seat |
*B | for Driver Side Power Seat |
|
*C | for Front Passenger Seat |
- | - |
|
*1 | Front Seat Belt Anchor Plate |
- | - |
.png) |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
- | - |
CAUTION / NOTICE / HINT
PROCEDURE
1. INSTALL FRONT SEAT INNER BELT ASSEMBLY
(a) for Driver Side Manual Seat:
|
*1 | Front Seat Belt Anchor Plate |
- | - |
.png) |
Protruding Part | - |
- |
(1) Install the front seat belt anchor plate as shown in the illustration.
(2) Install the front seat inner belt assembly with the nut.
Torque:
42 N·m {428 kgf·cm, 31 ft·lbf}
NOTICE:
Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the separate type front seat cushion spring assembly.
(3) Engage each clamp.
(b) for Driver Side Power Seat:
|
*1 | Front Seat Belt Anchor Plate |
- | - |
|
|
Protruding Part | - |
- |
(1) Install the front seat belt anchor plate as shown in the illustration.
(2) Install the front seat inner belt assembly with the nut.
Torque:
42 N·m {428 kgf·cm, 31 ft·lbf}
NOTICE:
Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the separate type front seat cushion spring assembly.
(3) Engage each clamp.
(c) for Front Passenger Seat:
|
*1 | Front Seat Belt Anchor Plate |
- | - |
|
|
Protruding Part | - |
- |
(1) Install the front seat belt anchor plate as shown in the illustration.
(2) Install the front seat inner belt assembly with the nut.
Torque:
42 N·m {428 kgf·cm, 31 ft·lbf}
NOTICE:
Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the separate type front seat cushion spring assembly.
(3) Engage each clamp.
2. CONNECT SEPARATE TYPE FRONT SEATBACK COVER
3. INSTALL FRONT SEAT ASSEMBLY
|
|
|
READ NEXT:
Precaution
PRECAUTION CAUTION: Replace any faulty parts of the seat belt systems (outer belt, inner belt, bolts, nuts, adjustable shoulder anchor, tether anchor hardware and other related parts). When inspecting
Removal
REMOVAL CAUTION / NOTICE / HINT COMPONENTS (REMOVAL)
Procedure Part Name Code
1 PRECAUTION
-
- -
2 CABLE FROM NEGATIVE AUXILIARY
SEE MORE:
On-vehicle Inspection
ON-VEHICLE INSPECTION PROCEDURE
1. INSPECT AUTOMATIC LIGHT CONTROL SENSOR (a) Disconnect the h1 automatic light control sensor connector.
(b) Measure the voltage and resistance according to the value(s) in the table below.
Standard Voltage:
Tester Connection Condition
Spec
Installation
INSTALLATION
CAUTION / NOTICE / HINT
COMPONENTS (INSTALLATION)
Procedure
Part Name Code
1
TIRE PRESSURE WARNING ECU AND RECEIVER
897B0A
-
-
2
ROO
