Toyota Corolla Cross: Dcm Operation History
DCM OPERATION HISTORY
HINT:
- This function shows the telematics network status when the DCM (telematics transceiver) was operated. Use this when no DTC is present but this telematics system was unable to connect to the call center. This symptom may occur if cell phone signal strength is very weak.
- This function is used to display operation history information and the time at which it was stored in the DCM (telematics transceiver).
DCM OPERATION HISTORY
(a) Enter the following menus: Body Electrical / Telematics / Utility / DCM Operation History
Body Electrical > Telematics > Utility|
Tester Display |
|---|
|
DCM Operation History |
(b) Choose "Items" on the DCM Operation History Menu.
HINT:
- When "Operation Code" is recorded, DCM Operation History is displayed on the GTS.
- The displayed "Function" differs depending on the selected "Items".
(c) Refer to the following chart and check the system operation status displayed on the GTS. (The following chart is an example of the system operation status.)
System Operation Status Example|
Occurrence Time*1 |
Operation Code*2 |
Function*3 |
Content*4 |
Roaming*5 |
Voice Call*6 |
Service Area*7 |
Electric Level*8 |
|---|---|---|---|---|---|---|---|
|
2017/12/31 12:40:50 |
0101 |
GNSS (Satellite) |
Unreceived GNSS (Satellite) signal |
ON |
With |
Out of Service |
Level 0 |
|
Tester Display |
Description |
Range |
||
|---|---|---|---|---|
|
*1 |
Occurrence time |
Indicates date of the DCM (telematics transceiver) operation. |
- |
|
|
*2 |
Operation Code |
Indicates the Operation Code. |
- |
|
|
*3 |
Function |
Items |
Indicates the function name. |
- |
|
Common |
|
|||
|
Emergency Call |
|
|||
|
*4 |
Content |
Indicates the content. |
- |
|
|
*5 |
Roaming |
Indicates whether roaming was used for the communication network. |
ON or OFF |
|
|
*6 |
Voice Call |
Indicates whether there was a voice call. |
With or Without |
|
|
*7 |
Service Area |
Indicates whether the vehicle was in the service area. |
Out of Service, Within Range, OFF the Air or Start up (LTE) |
|
|
*8 |
Electric Level |
Indicates the strength of the cellular signal received by the vehicle. |
Level 0, Level 1, Level2, Level3, Level 4, Level 5 |
|
READ NEXT:
Dcm Activation
DCM ACTIVATION
DCM ACTIVATION
(a) Enter the following menus:
Body Electrical > Telematics > Utility
Tester Display
VIN Synchronization
(b) According to
Acn Call End
ACN CALL END
ACN CALL END
This function terminates the ACN (Automatic Collision Notification)
to the telematics provider. After a collision in which the DCM receives "Collision
Detection Si
Customize Parameters
CUSTOMIZE PARAMETERS
CUSTOMIZE TELEMATICS SYSTEM
(a) Customizing with the GTS.
NOTICE:
When the customer requests a change in a function, first make sure that
the function can be customized
SEE MORE:
Tongue Plate Stopper
ComponentsCOMPONENTS ILLUSTRATION
*1 TONGUE PLATE STOPPER
- -
● Non-reusable part
- - ReplacementREPLACEMENT PROCEDURE
1. REMOVE TONGUE PLATE STOPPER
(a) Slide the tongue plate above the installation position of the tongue plate stopper, and tempora
Combination Switch
Inspection
INSPECTION
PROCEDURE
1. INSPECT DRIVE MODE SELECT SWITCH (COMBINATION SWITCH ASSEMBLY)
(a) Check the resistance.
(1) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condi
