Toyota Corolla Cross: Auto Up Operation does not Fully Close Power Window (Jam Protection Function is Activated)
DESCRIPTION
If a door glass does not slide smoothly or a power window regulator motor assembly or door window regulator sub-assembly does not operate smoothly, the jam protection function may be triggered automatically, resulting in the auto up operation being unable to fully close the power window.
CAUTION / NOTICE / HINT
NOTICE:
- If a power window regulator motor assembly has been replaced with a new one, initialize the power window control system.
Click here
.gif)
- If a power window regulator motor assembly and door window regulator sub-assembly have been removed and installed, or if a power window regulator motor assembly was reused when a door glass or door glass run was replaced, initialize the power window control system.
Click here
HINT:
This symptom may occur for any of the power windows.
PROCEDURE
| 1. |
PERFORM INITIALIZATION (APPLICABLE LOCATION) |
(a) Initialize the power window regulator motor assembly (applicable location).
Click here
|
.gif)
| 2. |
CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP / DOWN FUNCTION (APPLICABLE LOCATION)) |
(a) Check that each power window moves when the auto up and down functions of the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly are operated.
Click here
OK:
Auto up and down functions are normal (applicable location).
| OK | .gif) | END (PROBLEM DUE TO INITIALIZATION FAILURE) |
|
| 3. |
CHECK DOOR GLASS SLIDING MOVEMENT (APPLICABLE LOCATION) |
(a) Remove the power window regulator motor assembly and door window regulator sub-assembly.
(b) Install the door glass to the door glass run.
(c) Check that the power window regulator motor assembly and door window regulator sub-assembly operate smoothly.
(d) Check that the door glass slides smoothly when sliding it up by hand.
NOTICE:
Make sure to perform initialization again.
HINT:
Ensure the following:- The door glass fits in the door glass run without improper contact or deformation.
- Foreign matter is not caught in the door glass run.
- The door glass run is not misaligned.
- The door glass is not tilted and does not catch on the door glass run.
OK:
Door glass slides smoothly.
|
Result | Proceed to |
|---|---|
|
OK (Driver door power window) |
A |
| OK (Front passenger door power window) | |
|
OK (Rear LH door power window) |
B |
| OK (Rear RH door power window) | |
|
NG | C |
| A |
| REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door or Front Passenger Door)
|
| B |
| REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door or Rear RH Door)
|
| C |
| FIT DOOR GLASS CORRECTLY (REMOVE FOREIGN MATTER CAUSING IMPROPER FIT OR REPLACE PARTS) |
READ NEXT:
Auto Down Operation does not Fully Open Power Window (Catch Protection Function is Activated)
DESCRIPTION If a door glass does not slide smoothly or a power window regulator motor assembly or door window regulator sub-assembly does not operate smoothly, the catch protection function may be tri
Jam Protection Function does not Operate
DESCRIPTION This symptom may occur for any of the power windows.
The jam protection function operates within a specified range during the manual up or auto up operation. CAUTION / NOTICE / HINT
NOTI
Power Window Master Switch
RemovalREMOVAL CAUTION / NOTICE / HINT COMPONENTS (REMOVAL)
Procedure Part Name Code
1 MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANE
SEE MORE:
Brake Switch "A" Circuit Open (P057113)
DESCRIPTION
The skid control ECU (brake actuator assembly) receives stop
light switch assembly signals and uses them to determine whether or not the brakes
are applied.
The skid control ECU (brake actuator assembly) has a detection
circuit that it uses to detect an open in the stop light inp
Front Radar Sensor Optical Axis Misalignment Malfunction (C1A1100)
DESCRIPTION
The millimeter wave radar sensor assembly performs self-diagnosis
to check for misalignment of its beam axis. If misalignment is detected, the millimeter
wave radar sensor assembly stores DTC C1A1100.
DTC No.
Detection Item
DTC Detection Condition
