Toyota Corolla Cross: Tire Pressure Monitor Transmitter ID 1 Component Internal Failure (C214196-C214496)
DESCRIPTION
The tire pressure warning valve and transmitters that are installed in the tire and wheel assemblies measure the tire pressure of each wheel. The measured values are transmitted to the tire pressure warning ECU and receiver in the vehicle as radio waves. The ECU compares the measured tire pressure values with the tire pressure threshold. When the measured tire pressure value is less than this threshold, the warning light in the combination meter assembly illuminates.
When the internal circuit of a tire pressure warning valve and transmitter is malfunctioning, one of these DTCs is output.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
|---|---|---|---|
|
C214196 |
Tire Pressure Monitor Transmitter ID 1 Component Internal Failure |
Tire pressure warning valve and transmitter is malfunctioning |
Tire pressure warning valve and transmitter |
|
C214296 |
Tire Pressure Monitor Transmitter ID 2 Component Internal Failure |
Tire pressure warning valve and transmitter is malfunctioning |
Tire pressure warning valve and transmitter |
|
C214396 |
Tire Pressure Monitor Transmitter ID 3 Component Internal Failure |
Tire pressure warning valve and transmitter is malfunctioning |
Tire pressure warning valve and transmitter |
|
C214496 |
Tire Pressure Monitor Transmitter ID 4 Component Internal Failure |
Tire pressure warning valve and transmitter is malfunctioning |
Tire pressure warning valve and transmitter |
HINT:
It is necessary to perform the following procedure to identify the tire pressure warning valve and transmitter that is malfunctioning because it cannot be identified by the output DTC.
CAUTION / NOTICE / HINT
NOTICE:
- When replacing the tire pressure warning valve and transmitter, read the transmitter IDs and number of the transmitters stored in the old ECU using the GTS and write them down before removal.
- It is necessary to perform initialization after registration of the transmitter
IDs into the tire pressure warning ECU and receiver if one of the valve and
transmitters has been replaced.
for Registration:
Click here
.gif)
for Initialization:
Click here
PROCEDURE
|
1. |
IDENTIFY TRANSMITTER CORRESPONDING TO DTC (TIRE POSITION) |
(a) Display the "ID Tire Position" value for each wheel using the GTS.
(b) Refer to the following chart and check the wheel position of the DTC and transmitter match.
Chassis > Tire Pressure Monitor > Data List|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
ID 1 Tire Position |
ID1 tire position |
No Information, FL, FR, RL, RR, Spare or Judging |
ID1 tire position is displayed |
If no tire position information is stored, "No Information" will be displayed. |
|
ID 2 Tire Position |
ID2 tire position |
No Information, FL, FR, RL, RR, Spare or Judging |
ID2 tire position is displayed |
If no tire position information is stored, "No Information" will be displayed. |
|
ID 3 Tire Position |
ID3 tire position |
No Information, FL, FR, RL, RR, Spare or Judging |
ID3 tire position is displayed |
If no tire position information is stored, "No Information" will be displayed. |
|
ID 4 Tire Position |
ID4 tire position |
No Information, FL, FR, RL, RR, Spare or Judging |
ID4 tire position is displayed |
If no tire position information is stored, "No Information" will be displayed. |
|
Tester Display |
|---|
|
ID 1 Tire Position |
|
ID 2 Tire Position |
|
ID 3 Tire Position |
|
ID 4 Tire Position |
| NEXT | .gif) |
REPLACE CORRESPONDING TIRE PRESSURE WARNING VALVE AND TRANSMITTER for Aluminum Wheel Type: Click here for Steel Wheel Type: Click here |
READ NEXT:
Tire Pressure Monitor Module System Internal Failure (C217604)
DESCRIPTION
Tire pressure warning valve and transmitter signals are transmitted to the tire
pressure warning ECU and receiver in the vehicle as radio waves.
DTC No.
Detection
Lost Communication with Brake System Control Module "A" Missing Message (U012987)
DESCRIPTION
The tire pressure warning ECU and receiver receives signals from the skid control
ECU (brake actuator assembly) via the CAN communication system.
DTC No.
Detectio
Tire Pressure Warning Reset Switch Circuit
DESCRIPTION
The switch circuit inside the combination meter assembly turns on and off according
to the steering pad switch assembly operation.
WIRING DIAGRAM
PROCEDURE
1.
SEE MORE:
Dtc Check / Clear
DTC CHECK / CLEAR
HINT:
DTCs which are stored in the skid control ECU can be displayed on the
GTS. The GTS can display the confirmed and permanent DTCs.
If a malfunction is detected during the current driving cycle, confirmed
and permanent DTCs are stored.
Confirmed DTCs can be cl
Shift Lever Knob
Removal
REMOVAL
CAUTION / NOTICE / HINT
Procedure
Part Name Code
1
SHIFT LEVER KNOB SUB-ASSEMBLY
33504F
-
-
PROCEDURE
1. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY
