Toyota Corolla Cross: Right Rear Wheel Speed Sensor Incorrect Component Installed (C055895)
DESCRIPTION
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
|---|---|---|---|
|
C055895 |
Right Rear Wheel Speed Sensor Incorrect Component Installed |
The rear speed sensor RH is installed incorrectly. |
|
- *1: for AWD
- *2: for 2WD
PROCEDURE
|
1. |
CHECK PART NUMBER (REAR SPEED SENSOR RH) |
(a) Check that the rear speed sensor RH is installed.
OK:
Proper rear speed sensor RH is installed.
NOTICE:
If it is necessary to remove components in order to check the rear speed sensor RH, follow the relevant installation and removal procedures and precautions for those components.
HINT:
The rear speed sensor rotor RH and rear speed sensor RH are incorporated into the rear axle hub and bearing assembly RH. (for 2WD)
If the rear speed sensor rotor RH and rear speed sensor RH need to be replaced, replace them together with the rear axle hub and bearing assembly RH. (for 2WD)
| NG | .gif)
|
REPLACE REAR SPEED SENSOR RH for 2WD: Click here
for AWD: Click here
|
.gif)
|
.gif)
|
2. |
CLEAR DTC |
(a) Clear the DTCs.
Chassis > Brake/EPB > Clear DTCs(b) Turn the ignition switch off.
|
|
3. |
RECONFIRM DTC |
(a) Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
(b) Check if the same DTC is output.
Chassis > Brake/EPB > Trouble CodesHINT:
The rear speed sensor rotor RH and rear speed sensor RH are incorporated into the rear axle hub and bearing assembly RH. (for 2WD)
If the rear speed sensor rotor RH and rear speed sensor RH need to be replaced, replace them together with the rear axle hub and bearing assembly RH. (for 2WD)
|
Result |
Proceed to |
|---|---|
|
C055895 is not output |
A |
|
C055895 is output |
B |
| A |
|
USE SIMULATION METHOD TO CHECK |
| B |
|
REPLACE REAR SPEED SENSOR RH for 2WD: Click here
for AWD: Click here
|
READ NEXT:
Brake System Control Module "A" System Internal Failure (C059704)
DESCRIPTION
The skid control ECU (brake actuator assembly) stores this DTC
if malfunctions are found in a circuit inside the ECU by self-diagnosis.
DTC No.
Detection Item
Brake System Control Module "A" Calibration / Parameter Memory Failure (C059746)
DESCRIPTION
If the system information stored by the skid control ECU (brake
actuator assembly) is corrupted, this DTC is output.
DTC No.
Detection Item
DTC Detecti
ABS Pump Motor Drive Circuit Supply Voltage Circuit Voltage Below Threshold
(C116516)
DESCRIPTION
The ABS motor relay is built into the brake actuator assembly.
When the skid control ECU (brake actuator assembly) operates
ABS, TRAC, VSC, brake hold or brake assist, the ABS motor re
SEE MORE:
Positions for towing hitch
receiver and hitch ball
Weight carrying ball position:
37.5 in. (952.0 mm)
Hitch receiver pin hole position:
31.6 in. (801.5 mm)
Connecting trailer lights
Please consult your dealer
when installing trailer lights, as
incorrect installation may cause
damage to the vehicle's lights.
Please take care to comply with
yo
Transmission Wire
Removal
REMOVAL
CAUTION / NOTICE / HINT
COMPONENTS (REMOVAL)
Procedure
Part Name Code
1
TRANSMISSION VALVE BODY ASSEMBLY
35410J
-
-
-
2
TRANSMIS
