Toyota Corolla Cross: Installation
INSTALLATION
CAUTION / NOTICE / HINT
COMPONENTS (INSTALLATION).png)
|
Procedure | Part Name Code |
.png) |
.png) |
.png) | |
|---|---|---|---|---|---|
|
1 | FRONT SEATBACK HEATER ASSEMBLY |
87510L | - |
- | - |
|
2 | SEPARATE TYPE FRONT SEATBACK COVER |
71073S |
|
- | - |
|
*1 | SEPARATE TYPE FRONT SEATBACK PAD |
*2 | TAG PIN |
|
● | Non-reusable part |
- | - |
|
Procedure | Part Name Code |
|
|
| |
|---|---|---|---|---|---|
|
3 | SEPARATE TYPE FRONT SEATBACK COVER WITH PAD |
- | - |
- | - |
|
4 | FRONT SEAT HEADREST SUPPORT |
71931 |
|
- | - |
|
Procedure | Part Name Code |
|
|
| |
|---|---|---|---|---|---|
|
5 | SEPARATE TYPE FRONT SEATBACK ASSEMBLY |
- | - |
- | - |
.png) |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
- | - |
|
Procedure | Part Name Code |
|
|
| |
|---|---|---|---|---|---|
|
6 | FRONT SEAT INNER CUSHION SHIELD |
71862 | - |
- | - |
|
7 | FRONT SEAT CUSHION SHIELD |
71812D | - |
- | - |
|
8 | FRONT SEAT FRONT CUSHION SHIELD |
71868N | - |
- | - |
|
Procedure | Part Name Code |
|
|
| |
|---|---|---|---|---|---|
|
9 | SEPARATE TYPE FRONT SEATBACK COVER |
71073S | - |
- | - |
|
10 | FRONT SEAT ASSEMBLY |
- | - |
- | - |
CAUTION / NOTICE / HINT
CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.
.png)
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. INSTALL FRONT SEATBACK HEATER ASSEMBLY
2. INSTALL SEPARATE TYPE FRONT SEATBACK COVER
|
|
Click here |
3. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
4. INSTALL FRONT SEAT HEADREST SUPPORT
|
|
Click here |
5. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY
6. INSTALL FRONT SEAT INNER CUSHION SHIELD
7. INSTALL FRONT SEAT CUSHION SHIELD
8. INSTALL FRONT SEAT FRONT CUSHION SHIELD
9. CONNECT SEPARATE TYPE FRONT SEATBACK COVER
10. INSTALL FRONT SEAT ASSEMBLY
Click here .gif)
READ NEXT:
Removal
REMOVAL CAUTION / NOTICE / HINT COMPONENTS (REMOVAL)
Procedure Part Name Code
1 PRECAUTION
-
- -
2 FRONT SEAT ASSEMBLY
-
Inspection
INSPECTION PROCEDURE 1. INSPECT LUMBAR SUPPORT ADJUSTER ASSEMBLY
(a) Check the operation of the lumbar support adjuster assembly RH.
(1) Check that the front seatback moves forward and backwar
SEE MORE:
Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Battery or Open (P032515)
DESCRIPTION Refer to DTC P032511. Click here
HINT: When DTC P032515 is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. Fail-safe mode continues until the ignition switch is turned off.
DTC No. Detection Item
DT
How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT
HINT:
The power back door system troubleshooting procedure is based on the premise that the smart key system (for Entry Function) is operating normally. Check the power back door system first before troubleshooting the power back door system.
for HEV Model: Click here
