Toyota Corolla Cross: How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT
HINT:
- Use the following procedure to troubleshoot the sliding roof system.
- *: Use the GTS.
PROCEDURE
|
1. | VEHICLE BROUGHT TO WORKSHOP |
|
.gif)
| 2. |
CUSTOMER PROBLEM ANALYSIS |
HINT:
- In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
- Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
- The following 5 items are important points for problem analysis:
What
Vehicle model, system name
When
Date, time, occurrence frequency
Where
Road conditions
Under what conditions?
Driving conditions, weather conditions
How did it happen?
Problem symptoms
|
| 3. |
PRE-CHECK |
(a) Measure the auxiliary battery voltage with the ignition switch off.
Standard Voltage:
11 to 14 V
If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.
(b) Check the fuses and relays.
(c) Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.
|
| 4. |
INSPECT COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM* |
(a) Using the GTS, check for CAN communication system DTCs.
- for HEV Model:
Click here
.gif)
- for Gasoline Model:
Click here
|
Result | Proceed to |
|---|---|
|
CAN DTCs are not output |
A |
| CAN DTCs are output |
B |
| B |
.gif) | GO TO CAN COMMUNICATION SYSTEM for HEV Model: Click here for Gasoline Model: Click here
|
|
| 5. |
INSPECT COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM* |
(a) Using the GTS, check for LIN communication system DTCs.
Body Electrical > Main Body > Trouble Codes|
Result | Proceed to |
|---|---|
|
LIN DTCs are not output |
A |
| LIN DTCs are output |
B |
| B |
| GO TO LIN COMMUNICATION SYSTEM |
|
| 6. |
CHECK FOR DTC* |
(a) Check for DTCs and make a note of any codes that are output.
Body Electrical > Main Body > Trouble Codes(b) Clear the DTCs.
Body Electrical > Main Body > Clear DTCs(c) Recheck for DTCs.
Body Electrical > Main Body > Trouble Codes|
Result | Proceed to |
|---|---|
|
DTCs are not output | A |
|
DTCs are output | B |
| B |
| GO TO DIAGNOSTIC TROUBLE CODE CHART |
|
| 7. |
PROBLEM SYMPTOMS TABLE |
(a) Refer to Problem Symptoms Table.
Click here
|
Result | Proceed to |
|---|---|
|
Fault is not listed in Problem Symptoms Table |
A |
| Fault is listed in Problem Symptoms Table |
B |
| B |
| GO TO STEP 9 |
|
| 8. |
OVERALL ANALYSIS AND TROUBLESHOOTING* |
(a) Operation Check
Click here
(b) Terminals of ECU
Click here
(c) Data List / Active Test
Click here
(d) Inspection
|
| 9. |
ADJUST, REPAIR OR REPLACE |
(a) Check if the sliding roof drive gear sub-assembly has been replaced, or the sliding roof glass sub-assembly or sliding roof drive cable sub-assembly has been adjusted, or removed and installed.
|
Result | Proceed to |
|---|---|
|
The sliding roof drive gear sub-assembly has been replaced, or the sliding roof glass sub-assembly or sliding roof drive cable sub-assembly has been adjusted, or removed and installed. |
A |
| The sliding roof drive gear sub-assembly has not been replaced, and the sliding roof glass sub-assembly and sliding roof drive cable sub-assembly have not been adjusted, or removed and installed. |
B |
| B |
| GO TO STEP 11 |
|
| 10. |
INITIALIZE SLIDING ROOF SYSTEM |
(a) Initialize the sliding roof ECU (sliding roof drive gear sub-assembly).
Click here
|
| 11. |
CONFIRMATION TEST |
| NEXT | | END |
READ NEXT:
Operation Check
OPERATION CHECK CHECK AUTO OPERATION FUNCTION
NOTICE:
Make sure that initialization has been completed before performing this inspection.
Click here
The sliding roof auto operation can be custo
Customize Parameters
CUSTOMIZE PARAMETERS CUSTOMIZE SLIDING ROOF SYSTEM
NOTICE:
When the customer requests a change in a function, first make sure that the function can be customized.
Be sure to make a note of the c
Initialization
INITIALIZATION INITIALIZE SLIDING ROOF SYSTEM
NOTICE:
When the sliding roof glass sub-assembly or sliding roof drive cable sub-assembly is adjusted or removed/installed, or the sliding roof drive g
SEE MORE:
Installation
INSTALLATION
CAUTION / NOTICE / HINT
COMPONENTS (INSTALLATION)
Procedure
Part Name Code
1
TELEMATICS TRANSCEIVER
86741A
-
-
-
2
NO. 1 TELEPHONE BRA
Operation Check
OPERATION CHECK CHECK WINDSHIELD DEICER SYSTEM
(a) Turn the ignition switch to ON. (b) Check that the windshield deicer wire (windshield glass) becomes warm by operating the front wiper deicer switch.
(c) Confirm that windshield deicer system operation stops after approximately 15 minutes.
NOTICE
