Toyota Corolla Cross: Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch

DESCRIPTION

When the ignition switch is ON, the power window regulator motor assembly (for front passenger door) is operated by the power window regulator switch assembly. The power window regulator motor assembly (for front passenger door) has motor, regulator, and ECU functions.

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

NOTICE:

• Inspect the fuses for circuits related to this system before performing the following procedure.
• If the power window regulator motor assembly (for front passenger door) has been replaced with a new one, initialize the power window control system.

  Click here

• The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

  Click here

• Check that the window lock switch is off before performing the following procedure.
• Before replacing the main body ECU (multiplex network body ECU), refer to Registration.*1
  • for HEV Model:

    Click here

  • for Gasoline Model:

    Click here

  • *1: w/ Smart Key System

PROCEDURE

1.	READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List

Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
Communication P-Door Motor	Connection status between power window regulator motor assembly (for front passenger door) and main body ECU (multiplex network body ECU)	STOP or OK	STOP: Communication stopped OK: Normal communication	-

Body Electrical > Main Body > Data List

Tester Display
Communication P-Door Motor

OK:

OK is displayed for each Data List item above.

NG

GO TO LIN COMMUNICATION SYSTEM

OK

2.	READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List

Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
P Door Power Window UP Switch	Front passenger door power window manual up switch	OFF or ON	OFF: Manual up switch not being operated ON: Manual up switch being operated	-
P Door Power Window DOWN Switch	Front passenger door power window manual down switch	OFF or ON	OFF: Manual down switch not being operated ON: Manual down switch being operated	-

Body Electrical > Main Body > Data List

Tester Display
P Window Auto Up Function
P Window Auto Down Function

OK:

On the GTS screen, ON or OFF is displayed accordingly.

NG

GO TO STEP 4

OK

3.	PERFORM ACTIVE TEST USING GTS

(a) Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test

Tester Display	Measurement Item	Control Range	Diagnostic Note
P Door Power Window UP	Front passenger door power window up activate	OFF/ON	-
P Door Power Window DOWN	Front passenger door power window down activate	OFF/ON	-

Body Electrical > Main Body > Active Test

Tester Display
P Door Power Window UP

Body Electrical > Main Body > Active Test

Tester Display
P Door Power Window DOWN

HINT:

Up and down movement does not occur if the arrow is not pressed and held.

OK:

Front passenger door power window operates normally.

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

4.	INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY

Click here

NG

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY

OK

5.	CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR))

(a) Disconnect the K2 power window regulator motor assembly (for front passenger door) connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
K12-5 (UP) - K2-10 (UP)	Always	Below 1 Ω
K12-5 (UP) or K2-10 (UP) - Body ground	Always	10 kΩ or higher
K12-4 (DOWN) - K2-7 (DOWN)	Always	Below 1 Ω
K12-4 (DOWN) or K2-7 (DOWN) - Body ground	Always	10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

6.	INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

Click here

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

READ NEXT: