Toyota Corolla Cross: Fail-safe Chart

P001001

P001600

P136001

P136201

P261401

Cam timing control motor with EDU assembly

The cam timing control motor with EDU assembly is operated to the most retarded position.

Pass condition detected and then ignition switch turned off

P001100

P001200

VVT system

Idling up (misfire prevention), or the cam timing control motor with EDU assembly is operated to the most retarded position.

Pass condition detected and then ignition switch turned off

P001500

VVT system

• Idle up (control of combustion worsening).
• Stopping fuel-cut control

Pass condition detected

P003012

P003013

P101A9E

Air fuel ratio sensor (sensor 1) heater

The ECM turns off the air fuel ratio sensor (sensor 1) heater.

Ignition switch off

P003612

P003613

P102A9E

Air fuel ratio sensor (sensor 2) heater

The ECM turns off the air fuel ratio sensor (sensor 2) heater.

Ignition switch off

P008700

P008800

P123513

Fuel pump assembly (for high pressure side)

• The ECM performs fuel-cut when the engine speed and engine load are high.
• Fuel pressure is set to 200 kPa (29 psi)

Ignition switch off

P010012

P010014

Mass air flow meter sub-assembly

The ECM calculates ignition timing according to the engine speed and throttle valve position.

Pass condition detected and then ignition switch turned off

P011011

P011015

Intake air temperature sensor

The ECM estimates the intake air temperature to be 20°C (68°F).

Pass condition detected and then ignition switch turned off

P011511

P011515

Engine coolant temperature sensor

The ECM estimates the engine coolant temperature to be 80°C (176°F).

Pass condition detected

P012011

P012015

P01201C

P022011

P022015

P060444

P060647

P060747

P060787

P060D49

P060E49

P065714

P06579E

P160700

P16B09F

P210018

P210019

P211172

P211173

P211900

P211904

P211977

P21199B

P21352B

Electronic throttle control system

The ECM cuts off throttle actuator current and the throttle valve is returned to a 7.5° throttle position by the return spring.

The ECM then adjusts the engine output by controlling fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal angle to allow the vehicle to be driven at a low speed*1.

Pass condition detected and then ignition switch turned off

P019011

P019015

Fuel pressure sensor (for high pressure)

• The ECM performs fuel-cut when the engine speed and engine load are high.
• Fuel pressure is set to 200 kPa (29 psi)

Pass condition detected and then ignition switch turned off

P020113

P020213

P020313

P020413

P062D13

ECM (injector driver)

The ECM performs fuel-cut when the engine speed is 2000 rpm or more.

Pass condition detected and then ignition switch turned off

P030000

P030027

P030085

P030100

P030200

P030300

P030400

*2

• Fuel injector assembly
• Electronic throttle control system

When a catalyst-damaging misfire occurs (MIL blinking), the following fail-safe operation is performed for catalyst overheat malfunction prevention.

1. Under a low load and at a low engine speed:

   - Fuel cut is performed on the malfunctioning cylinder.

2. Under a high load and at a high engine speed:

   - Throttle valve opening angle control is performed.

   - Fuel cut is performed on all cylinders or the malfunctioning cylinder.

Pass condition detected and then ignition switch turned off

P032511

P032515

Knock control sensor

The ECM sets the ignition timing to maximum retard.

Ignition switch off

P040000

P04019C

P04029B

P040318

P040319

P140018

P140019

EGR valve assembly

The ECM fully closes the EGR valve and stops EGR control.

Pass condition detected

P05042B

Stop light switch assembly

The accelerator pedal opening angle is fixed when there is an accelerator pedal malfunction or history of a malfunction.

Pass condition detected and then ignition switch turned off

P052012

P052014

P052024

P05202A

Oil pressure sensor

Current to the oil pressure control valve assembly is cut in order to fully close the oil pressure control valve assembly so that the pump operates at maximum capacity.

Pass condition detected and then ignition switch turned off

P052477

P15F009

P15F077

Engine oil pressure control system

• Current to the oil pressure control valve assembly is cut in order to fully close the oil pressure control valve assembly so that the pump operates at maximum capacity.
• The maximum engine speed is limited in accordance with the abnormal pressure.

Pass condition detected and then ignition switch turned off

P056014

ECM +B circuit

Generator command is maintained.

Pass condition detected and then ignition switch turned off

P06DA13

Oil pressure control valve assembly

Current to the oil pressure control valve assembly is cut in order to fully close the oil pressure control valve assembly so that the pump operates at maximum capacity.

Pass condition detected and then ignition switch turned off

P107A11

P107A15

No. 2 fuel pressure sensor (for low pressure side)

• Fuel pump (for low pressure side) control is maintained.
• Output power is limited.

Pass condition detected and then ignition switch turned off

P15F109

Engine oil pressure control system

• Current to the oil pressure control valve assembly is cut in order to fully close the oil pressure control valve assembly so that the pump operates at maximum capacity.
• Output power is limited.

Pass condition detected and then ignition switch turned off

P15F177

Engine oil pressure control system

Current to the oil pressure control valve assembly is cut in order to fully close the oil pressure control valve assembly so that the pump operates at maximum capacity.

Pass condition detected and then ignition switch turned off

P212012

P212014

P21201C

P21201F

P212099

P212512

P212514

P21251F

P21382B

Accelerator pedal sensor assembly

The accelerator pedal position sensor has 2 sensor circuits: Main and Sub.

If either circuit malfunctions, the ECM limits the engine output.

If both circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles.

Pass condition detected and then ignition switch turned off

P21CF13

P21D013

P21D113

P21D213

Port fuel injector assembly

The ECM performs fuel-cut when the engine speed is 2000 rpm or more.

Pass condition detected and then ignition switch turned off

P222611

P222615

Atmospheric pressure sensor (ECM)

The ECM maintains the last learned atmospheric pressure value.

Pass condition detected

P223711

P223712

P223713

P223716

P223717

P22371B

P225111

P225112

Air fuel ratio sensor (sensor 1)

Air fuel ratio sensor (sensor 1) air fuel ratio feedback control is stopped.

Pass condition detected and then ignition switch turned off

P22AB11

P22AB12

P22AB13

P22AB16

P22AB17

P22B211

P22B212

Air fuel ratio sensor (sensor 2)

• Control based on air fuel ratio sensor (sensor 2) air fuel ratio feedback is stopped.
• The ECM turns off the air fuel ratio sensor (sensor 2) heater.

Pass condition detected and then ignition switch turned off

P26CA12

P26CA31

P26CB71

Engine water pump assembly

When the engine coolant temperature reaches 105°C (221°F), the engine speed is limited to 2500 rpm or less.

Pass condition detected and then ignition switch turned off

P26CA14

Engine water pump assembly

• When the engine coolant temperature reaches 105°C (221°F), the engine speed is limited to 2500 rpm or less.
• The engine water pump assembly is controlled at a duty ratio of 85%.

Pass condition detected and then ignition switch turned off

P26CE37

Engine water pump assembly

The engine water pump assembly is temporarily operated and stopped in a repeating cycle.

• Output duty ratio of the WPO terminal repeats a cycle of 0% for 0 to 5 seconds and then 85% for 5 to 30 seconds.

Pass condition detected and then ignition switch turned off