Toyota Corolla Cross: Data List / Active Test
DATA LIST / ACTIVE TEST
DATA LIST
HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
(a) Enter the following menus: Body Electrical / Back Door or Main Body / Data List.
(b) According to the display on the GTS, read the Data List.
- *: Although the item is displayed on the GTS, it is not applicable to this vehicle.
|
Tester Display | Measurement Item |
Range | Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Total Distance Traveled |
Total distance traveled |
0 to 16777215 | Same as actual total distance traveled |
For the unit, refer to "Total Distance Traveled - Unit" |
|
Total Distance Traveled - Unit |
Total Distance Traveled - Unit |
km or mile | km: km mile: mile | - |
|
Back Door Lock Status | Back door condition signal |
Lock or Unlock | Lock: Back door locked Unlock: Back door unlocked |
- |
| Half Latch Switch |
Latch switch signal | ON or OFF |
ON: Back door lock motor open-latched OFF: Back door lock motor full-latched or half-latched |
- |
| Closer Position Switch |
Initial switch signal | ON or OFF |
ON: Back door lock sector gear in center position (Initial switch on) OFF: Back door lock sector gear out of center position (Initial switch off) |
- |
| Pawl Switch |
Pawl switch signal | ON or OFF |
ON: Back door lock motor open-latched OFF: Back door lock motor except openlatched |
- |
| Courtesy Switch |
Back door courtesy switch signal |
ON or OFF | ON: Back door open OFF: Back door closed |
- |
| PBD Main Switch |
Power back door ON/OFF signal |
ON or OFF | ON: Power back door ON OFF: Power back door off |
- |
| PBD Close Switch |
No. 1 power back door control switch signal |
ON or OFF | ON: No. 1 power back door control switch pushed OFF: No. 1 power back door control switch not pushed |
- |
| IG Switch |
Ignition switch signal |
ON or OFF | ON: Ignition switch ON OFF: Ignition switch off |
"OFF" is also displayed for this item when the ignition switch to ACC. |
|
Close and Lock Switch | Back door control switch signal |
OFF or ON | ON: Back door control switch pressed OFF: Back door control switch not pressed |
- |
| Door Lock Signal |
Back door condition signal |
Lock or Unlock | Lock: Back door locked Unlock: Back door unlocked |
- |
| PBD Touch Sensor RH |
Power back door sensor assembly RH signal |
ON, OFF or Open | ON: Power back door sensor assembly RH pressed OFF: Power back door sensor assembly RH not pressed Open: Power back door sensor assembly RH circuit open |
- |
| PBD Touch Sensor LH |
Power back door sensor assembly LH signal |
ON, OFF or Open | ON: Power back door sensor assembly LH pressed OFF: Power back door sensor assembly LH not pressed Open: Power back door sensor assembly LH circuit open |
- |
| Correction of Back Door Position |
Correction of back door position |
Not Complied With or Complied With |
Not Complied With: not complied with Complied With: complied with |
- |
| Opened Number of Times |
Number of times for back door opened |
0 to 214783647 | Number of times for back door opened |
- |
| Closed Number of Times |
Number of times for back door closed |
0 to 214783647 | Number of times for back door closed |
- |
| PBD SW Operating Condition Setting |
Back door control switch operation |
ON or 0.8s | Current customize setting displayed |
- |
| PBD Buzzer Function |
Status of the the power back door buzzer |
OFF or ON | Current customize setting displayed |
- |
| PBD Assist Close Function |
Function that enables/disables the power back door assist close operation. When set to ON, the back door will close automatically when operated in the close direction manually. |
OFF or ON | Current customize setting displayed |
- |
| PBD Assist Open Function |
Function that enables/disables the power back door assist open operation. When set to ON, the back door will open automatically when the back door opener switch assembly (open switch) is operated. |
OFF or ON | Current customize setting displayed |
- |
| PBD Door Unlock with One Motion Setting |
Door or doors to be unlocked when back door locked and power back door operated by pressing transmitter switch (electrical key transmitter sub-assembly). |
Back Door or All Doors |
Current customize setting displayed |
- |
| PBD Wireless Function |
Function that operates the power back door by pushing the transmitter switch (electrical key transmitter sub-assembly). |
OFF or ON | Current customize setting displayed |
- |
| PBD Wireless One Motion Function |
Wireless one motion function |
OFF or ON | Current customize setting displayed |
- |
| PBD Wireless SW Setting |
Wireless operation setting condition |
Time ON, 2 Times ON or Long |
Current customize setting displayed |
- |
|
Tester Display | Measurement Item |
Range | Diagnostic Note |
|---|---|---|---|
|
Back Door Lock Position Status |
Back door lock position signal |
Lock or Unlock | Lock: Back door locked Unlock: Back door unlocked |
|
Back Door Courtesy Switch Status |
Back door courtesy light switch signal |
Close or Open | Close: Back door closed Open: Back door open |
|
Back Door Operation Switch (Instrument) |
Power back door control switch signal |
ON or OFF | ON: Power back door control switch on OFF: Power back door control switch off |
ACTIVE TEST
HINT:
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
(a) Enter the following menus: Body Electrical / Back Door / Active Test.
(b) According to the display on GTS perform the "Active Test".
Body Electrical > Back Door > Active Test|
Tester Display | Measurement Item |
Control Range | Diagnostic Note |
|---|---|---|---|
|
PBD Motor (Open) | Power back door motor operation |
Start | - |
|
PBD Motor (Close) | Power back door motor operation |
Start | - |
|
PBD Buzzer (Small Volume) |
Power back door warning buzzer sound (small volume) |
Start | - |
|
PBD Buzzer (Middle Volume) |
Power back door warning buzzer sound (Middle volume) |
Start | - |
|
PBD Buzzer (Large Volume) |
Power back door warning buzzer sound (Large volume) |
Start | - |
|
PBD Release Closer | Latch release operation |
Start | - |
|
Courtesy Lamp | Power back door close switch light condition |
Start | - |
READ NEXT:
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART Power Back Door System
DTC No. Detection Item
Link B222049
Back Door Motor Internal Electronic Failure
B222631 PBD Unit Pulse Sensor
VEHICLE CONTROL HISTORY (RoB)
VEHICLE CONTROL HISTORY (RoB)
NOTICE:
If the vehicle or vehicle controls are operated (for example, during initial inspection when the vehicle is brought in for repair) before vehicle control histo
Back Door Motor Internal Electronic Failure (B222049)
DESCRIPTION This DTC is stored when the multiplex network door ECU detects a malfunction of the motor built-into the power back door unit assembly set LH or power back door unit assembly set RH.
SEE MORE:
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
HINT:
Use the table below to help determine the cause of problem symptoms. If multiple
suspected areas are listed, the potential causes of the symptoms are listed in order
of probability in the "Suspected Area" column of the table. Check each symptom by
check
Right Front Wheel Speed Sensor Internal Electronic Failure (C050649)
DESCRIPTION
When the system is starting up and the skid control ECU (brake
actuator assembly) detects a speed sensor circuit malfunction via the speed sensor
circuit self-diagnosis function, this DTC is stored.
DTC No.
Detection Item
DTC Detection Condition
