Toyota Corolla Cross: Customize Parameters
CUSTOMIZE PARAMETERS
CUSTOMIZE POWER BACK DOOR SYSTEM
HINT:
The following items can be customized.
NOTICE:
- When the customer requests a change in a function, first make sure that the function can be customized.
- Record the current settings before customizing.
(a) Customizing with the GTS.
(1) Enter the following menus: Customize Setting / PSD & PBD operation.
(2) Select the setting by referring to the table below.
PSD & PBD operation|
Tester Display | Description |
Default | Setting |
ECU |
|---|---|---|---|---|
| PBD SW Operating Condition Setting |
Back door control switch operation |
0.8s | $00:ON,$01:0.8s |
Multiplex network door ECU |
|
PBD Buzzer Function | Status of the the power back door buzzer |
ON | $00:OFF,$01:ON |
Multiplex network door ECU |
|
PBD Assist Close Function |
Function that enables/disables the power back door assist close operation. When set to ON, the back door will close automatically when operated in the close direction manually. |
ON | $00:OFF,$01:ON |
Multiplex network door ECU |
|
PBD Assist Open Function |
Function that enables/disables the power back door assist open operation. When set to ON, the back door will open automatically when the back door opener switch assembly (open switch) is operated. |
ON | $00:OFF,$01:ON |
Multiplex network door ECU |
|
PBD Door Unlock with One Motion Setting |
Function that selects the door or doors to unlock when the back door is locked and the electrical key transmitter sub-assembly (electrical key) is pushed to operate the power back door.* |
ALL DOORS | $00:Back Door,$01:All Doors |
Multiplex network door ECU |
|
PBD Wireless Function | Function that operates the power back door by pushing the transmitter switch (electrical key transmitter sub-assembly). |
ON | $00:OFF,$01:ON |
Multiplex network door ECU |
|
PBD Wireless One Motion Function |
Wireless one motion function |
ON | $00:OFF,$01:ON |
Multiplex network door ECU |
|
PBD Wireless SW Setting |
Wireless operation setting condition |
Long | $00:1 Time ON,$01:2 Times ON,$02:Long |
Multiplex network door ECU |
- *: The settings are enabled only when "PBD Wireless Function" is set to "ON".
(b) Customizing with the combination meter assembly
(1) Turn the ignition switch ON.
(2) Enter the following menus: Settings.
(3) Select the setting by referring to the table below.
|
Display | Description |
Default | Setting |
Relevant ECU |
|---|---|---|---|---|
| System Settings |
Function that enables or disables the power back door operation. |
On | On or Off |
Multiplex network door ECU |
|
Opening Adjustment | Function that can be used to set the power back door opening angle at 6 different positions. |
5 | User Setting Position, 5, 4, 3, 2 or 1 |
Multiplex network door ECU |
|
Volume | Function that can be used to set the power back door buzzer volume. |
large | large, normal or small |
Multiplex network door ECU |
READ NEXT:
Initialization
INITIALIZATION INITIALIZE MULTIPLEX NETWORK DOOR ECU
NOTICE: Initialization of the multiplex network door ECU (back door initial position learning) is necessary if the following work procedures are p
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE NOTICE: If the multiplex network door ECU has been removed and installed or replaced, or if any of the connectors has been disconnected, initialize the power back door system.
Terminals Of Ecu
TERMINALS OF ECU CHECK MULTIPLEX NETWORK DOOR ECU
(a) Disconnect the U39, U40, U41 and U42 multiplex network door ECU connectors.
(b) Measure the voltage and resistance according to the value(s) in
SEE MORE:
Software Incompatibility with Body Control Module Not Programmed (U032251,U032257)
DESCRIPTION
This DTC is stored when the destination information of the main
body ECU (multiplex network body ECU) does not match that of the blind spot monitor
sensors.
DTC No.
Detection Item
DTC Detection Condition
Trouble Area
U032
Installation
INSTALLATION
CAUTION / NOTICE / HINT
COMPONENTS (INSTALLATION)
Procedure
Part Name Code
1
REAR NO. 1 SPRING BUMPER
48341B
-
-
-
2
REAR SUSPENSION S
