Toyota Corolla Cross: Customize Parameters
CUSTOMIZE PARAMETERS
CUSTOMIZE INTUITIVE PARKING ASSIST SYSTEM
(a) Customize using GTS
(1) Select the setting by referring to the table below.
Clearance Warning|
Tester Display |
Description |
Default |
Setting |
ECU |
|---|---|---|---|---|
|
Ultrasonic Sensor (Front Center) Detection Range |
Sets the onset range of the ultrasonic sensor (front center). |
Far |
$00:Close,$01:Far |
Clearance warning ECU assembly |
|
Ultrasonic Sensor (Front Corner) Detection Range |
Sets the onset range of the ultrasonic sensor (front corner). |
Far |
$00:Close,$01:Far |
Clearance warning ECU assembly |
|
Ultrasonic Sensor (Rear Center) Detection Range |
Sets the onset range of the ultrasonic sensor (rear center). |
Far |
$00:Close,$01:Far |
Clearance warning ECU assembly |
|
Ultrasonic Sensor (Rear Corner) Detection Range |
Sets the onset range of the ultrasonic sensor (rear corner). |
Far |
$00:Close,$01:Far |
Clearance warning ECU assembly |
|
Clearance Warning Buzzer Volume |
Sets the volume of the clearance warning buzzer. |
Volume2 |
$01:Volume1,$02:Volume2,$03:Volume3 |
Clearance warning ECU assembly |
|
PKSA (O) Forward Detection Image Display |
Sets whether to show the sonar detection status on the display, when an obstacle is detected while driving the vehicle forward. |
Display |
$01:Display,$03:Hide |
Clearance warning ECU assembly |
|
Ultrasonic Sensor Actuation (Shift N) |
Turns ultrasonic sensor operation ON/OFF when shift position is in N. |
ON |
$00:OFF,$01:ON |
Clearance warning ECU assembly |
|
PKSA (O) Switch State Stored |
Sets whether to store the main switch status (ON/OFF). |
Stored |
$00:Not Stored,$01:Stored |
Clearance warning ECU assembly |
|
PKSA (O) Judgment of Obstacle on Course |
Sets whether to enable auto mute in the following situation, among the auto mute conditions for the auto mute function. (Obstacle is not in path of own vehicle.) |
Valid |
$00:Valid,$01:Invalid |
Clearance warning ECU assembly |
|
PKSA (O) Auto Mute Function |
Sets the availability of the auto mute function. |
ON |
$00:ON,$01:OFF |
Clearance warning ECU assembly |
|
PKSA (O) Image Display when Away from the Obstacle |
Sets whether to show the sonar detection status on the display when the vehicle moves away from the obstacle. |
Display |
$00:Hide,$01:Display |
Clearance warning ECU assembly |
(b) Customize using multi-information display
(1) Select the setting by referring to the table below.
Parking Assist|
Display |
Measurement Item |
Default |
Setting |
ECU |
|---|---|---|---|---|
|
Volume |
Setting of the clearance warning buzzer volume |
2 |
1, 2 or 3 |
Clearance warning ECU assembly |
READ NEXT:
Calibration
CALIBRATION
NOTICE:
When any of the following parts have been replaced, perform adjustment
shown in the following table. If not, the intuitive parking assist system may not
operate correctly.
A
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
NOTICE:
The vehicle is equipped with a Supplemental Restraint System (SRS) which
includes components such as airbags. Before servicing (including removal
or install
Terminals Of Ecu
TERMINALS OF ECU
CLEARANCE WARNING ECU ASSEMBLY
(a) Disconnect the I24 clearance warning ECU assembly connector.
(b) Measure the voltage and resistance on the wire harness side
connector accord
SEE MORE:
Removal
REMOVAL
CAUTION / NOTICE / HINT
COMPONENTS (REMOVAL)
Procedure
Part Name Code
1
ECM
89661
-
-
-
2
AUXILIARY BATTERY
-
-
Lost Communication with Air Inlet Damper Control Servo Motor LIN Missing Message (B143A87)
DESCRIPTION The air conditioning harness assembly and No. 1 air conditioning radiator damper servo sub-assembly connect the air conditioning amplifier assembly and the No. 1 blower damper servo sub-assembly. The air conditioning amplifier assembly supplies power and sends operation instructions to N
