Toyota Corolla Cross: Ultrasonic Sensor (Front Left Center) Component Internal Failure (C1AE296)
DESCRIPTION
The front center ultrasonic sensor (FLC sensor) is installed on the front bumper. The clearance warning ECU assembly detects obstacles based on signals it receives from the front center ultrasonic sensor (FLC sensor). If an open circuit or other malfunction occurs in the front center ultrasonic sensor (FLC sensor), the front center ultrasonic sensor (FLC sensor) does not operate correctly.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
|---|---|---|---|
|
C1AE296 |
Ultrasonic Sensor (Front Left Center) Component Internal Failure |
Front center ultrasonic sensor (FLC sensor) failure |
|
CAUTION / NOTICE / HINT
NOTICE:
- Perform registration after replacing or removing and installing the
ultrasonic sensor or clearance warning ECU assembly.
Click here
.gif)
- If a DTC is detected again after the repair, turn the ignition switch to ON and turn the intuitive parking assist system on, and then clear the DTC.
PROCEDURE
|
1. |
CLEAR DTC |
(a) Clear the DTCs.
Body Electrical > Clearance Warning > Clear DTCs
|
.gif)
|
2. |
CHECK FOR DTC |
(a) Check for DTCs.
Body Electrical > Clearance Warning > Trouble Codes|
Result |
Proceed to |
|---|---|
|
DTCs are not output |
A |
|
C1AE296 and C1AE287 are output |
B |
|
C1AE296 is output |
C |
|
None of the above conditions are met |
D |
| A | .gif)
|
USE SIMULATION METHOD TO CHECK |
| B |
|
GO TO DTC (C1AE287) |
| D |
|
GO TO DTC CHART
|
|
|
3. |
REPLACE FRONT CENTER ULTRASONIC SENSOR (FLC SENSOR) |
(a) Replace the front center ultrasonic sensor (FLC sensor) with a known good one.
HINT:
- Click here
- All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.
|
|
4. |
CLEAR DTC |
(a) Clear the DTCs.
Body Electrical > Clearance Warning > Clear DTCs
|
|
5. |
CHECK FOR DTC |
(a) Check for DTCs.
Body Electrical > Clearance Warning > Trouble Codes|
Result |
Proceed to |
|---|---|
|
DTCs are not output |
A |
|
C1AE296 is output |
B |
|
None of the above conditions are met |
C |
| A |
|
END (FRONT CENTER ULTRASONIC SENSOR [FLC SENSOR] WAS DEFECTIVE) |
| B |
|
REPLACE CLEARANCE WARNING ECU ASSEMBLY
|
| C |
|
GO TO DTC CHART
|
READ NEXT:
Ultrasonic Sensor (Front Right Center) Missing Message (C1AE387)
DESCRIPTION
This DTC is output when an open circuit or short occurs in the
communication line between a front center ultrasonic sensor (FRC sensor) and the
front center ultrasonic sensor (FLC sen
Ultrasonic Sensor (Front Right Center) Component Internal Failure (C1AE396)
DESCRIPTION
The front center ultrasonic sensor (FRC sensor) is installed
on the front bumper. The clearance warning ECU assembly detects obstacles based
on signals it receives from the front cent
Ultrasonic Sensor (Front Right Corner) Missing Message (C1AE487)
DESCRIPTION
This DTC is output when an open circuit or short occurs in the
communication line between a front corner ultrasonic sensor (FR sensor) and the
front center ultrasonic sensor (FRC sens
SEE MORE:
Drive Motor "B" Position Sensor Circuit Voltage Below Threshold (P0A4516,P0A451F)
DTC SUMMARY MALFUNCTION DESCRIPTION These DTCs indicate that the resolver output signal is abnormal. The cause of this malfunction may be one of the following:
Area Main Malfunction Description
Inverter low-voltage circuit
The connectors are not connected properly
R
Installation
INSTALLATION
CAUTION / NOTICE / HINT
COMPONENTS (INSTALLATION)
Procedure
Part Name Code
1
FRONT DRIVE SHAFT HOLE SNAP RING
43420G
-
-
2
FRONT DRI
