Toyota Corolla Cross: Removal

REMOVAL

CAUTION / NOTICE / HINT

Procedure		Part Name Code
1	PRECAUTION	-		-	-
2	CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL	-	-	-	-
3	REAR CENTER SEAT OUTER BELT ASSEMBLY	73350C	-	-	-
4	BENCH TYPE REAR SEAT CUSHION ASSEMBLY	-		-	-
5	REAR SEAT CUSHION LOCK HOOK	72693	-	-	-

Procedure		Part Name Code
6	FRONT DOOR SCUFF PLATE	67914B	-	-	-
7	FRONT DOOR OPENING TRIM WEATHERSTRIP	62312B	-	-	-
8	REAR DOOR SCUFF PLATE	67918A	-	-	-
9	REAR DOOR OPENING TRIM WEATHERSTRIP	62332A	-	-	-
10	LAP BELT OUTER ANCHOR COVER	73233	-	-	-
11	FRONT SEAT OUTER BELT ASSEMBLY	73220	-	-	-
12	CENTER PILLAR LOWER GARNISH	62414A	-	-	-
13	CENTER PILLER GARNISH ASSEMBLY	62420A	-	-	-

Procedure		Part Name Code
14	FRONT SEAT OUTER BELT ASSEMBLY	73220		-	-
15	FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY	73200A	-	-	-

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the front seat outer belt assembly removal/installation are shown below.

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click here

HINT:

• When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
  • Learning completes when vehicle is driven

    Effect / Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
    *A: for Gasoline Model
    Front Camera System	Drivre the vehicle straight ahead at 15 km/h (10mph) or more for 1 second or more.
    Stop and start system *A	Drive the vehicle until stop and start control is permitted (appoximately 5 to 60 minutes)

  • Learning completes when vehicle is operated normally

    Effect / Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
    Power door lock control system Back door opener	Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.
    Power back door system	Fully close the back door by hand. HINT: Initialization is not necessary if the above procedures are performed while the back door is closed.
    Air conditioning system	After the ignition switch is turned to ON, the servo motor standard position is recognized.	-

• Use the same procedure for RHD and LHD vehicles.
• The procedure listed below is for LHD vehicles.

PROCEDURE

1. PRECAUTION

CAUTION: Be sure to read Precaution thoroughly before servicing. Click here NOTICE: After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal. Click here

2. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system. If the airbag deploys for any reason, it may cause a serious accident.

• for Gasoline Model:

  Click here

• for HEV Model:

  Click here

3. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Gasoline Model)

Click here

4. REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY (for Gasoline Model)

Click here

5. REMOVE REAR SEAT CUSHION LOCK HOOK (for Gasoline Model)

Click here

6. REMOVE FRONT DOOR SCUFF PLATE

Click here

7. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

8. REMOVE REAR DOOR SCUFF PLATE

Click here

9. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

10. REMOVE LAP BELT OUTER ANCHOR COVER

11. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY

12. REMOVE CENTER PILLAR LOWER GARNISH

Click here

13. REMOVE CENTER PILLER GARNISH ASSEMBLY

Click here

14. REMOVE FRONT SEAT OUTER BELT ASSEMBLY

(1) Remove the nut and disconnect the shoulder anchor of the front seat outer belt assembly.

(2) Disconnect the pretensioner connector.

HINT:

Refer to How to Connector or Disconnect Airbag Connector:

Click here

(3) Remove the bolt.

(4) Disengage the 2 guides to remove the front seat outer belt assembly.

15. REMOVE FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

READ NEXT: