Toyota Corolla Cross: Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
If DTCs are not output but the malfunction persists, use the following table to determine which circuits to inspect for each problem symptom.
HINT:
Refer to each inspection procedure for related problem symptoms.
Electronically Controlled Brake System|
Symptom |
Suspected Area |
Link |
|---|---|---|
|
ABS warning light abnormal (Remains on) |
Refer to the procedure for "ABS Warning Light Remains ON" |
|
|
ABS warning light abnormal (Does not come on) |
Refer to the procedure for "ABS Warning Light does not Come ON" |
|
|
Brake system warning light (red indicator) abnormal (Remains on) |
Refer to the procedure for "Brake Warning Light Remains ON" |
|
|
Brake system warning light (red indicator) abnormal (Does not come on) |
Refer to the procedure for "Brake Warning Light does not Come ON" |
|
|
Brake hold standby indicator light abnormal |
Refer to the procedure for "Brake Hold Standby Indicator Light Circuit" |
|
|
Brake hold operated indicator light abnormal |
Refer to the procedure for "Brake Hold Operated Indicator Light Circuit" |
|
|
Slip indicator light abnormal (Remains on) |
Refer to the procedure for "Slip Indicator Light Remains ON" |
|
|
Slip indicator light abnormal (Does not come on) |
Refer to the procedure for "Slip Indicator Light does not Come ON" |
|
|
TRAC does not operate |
Refer to the procedure for "TRAC does not Operate" |
|
|
Excessive brake pedal travel (No fluid leaks and no air in system) |
Refer to the procedure for "Excessive Brake Pedal Travel (No Fluid Leaks and No Air in System)" |
|
|
ABS operates before necessary when braking |
Refer to the procedure for "ABS Operates Before Necessary When Braking" |
|
|
VSC does not operate or VSC does not operate correctly |
Refer to the procedure for "VSC does not Operate or VSC does not Operate Correctly" |
|
|
Brake actuator operation sound is loud during initial check |
Refer to the procedure for "Brake Actuator Operation Sound is Loud during Initial Check" |
|
|
VSC OFF switch abnormal |
Refer to the procedure for "VSC OFF Switch Circuit" |
|
.gif)
READ NEXT:
Terminals Of Ecu
TERMINALS OF ECU
TERMINAL INSPECTION
(a) Disconnect the A151 skid control ECU (brake actuator assembly)
connector and measure the voltage and resistance on the wire harness side.
*a
Dtc Check / Clear
DTC CHECK / CLEAR
DTC CHECK
(a) Turn the ignition switch off.
(b) Connect the GTS to the DLC3.
(c) Turn the ignition switch to ON.
(d) Turn the GTS on.
(e) Read the DTCs following the prompts on
Freeze Frame Data
FREEZE FRAME DATA
FREEZE FRAME DATA/INFORMATION
(a) Using the GTS, check the vehicle condition (ECU, sensor) when
the brake system operates or a DTC is output.
CHECK FREEZE FRAME DATA AND INFORMA
SEE MORE:
Generator Inverter Stuck On (P0A7A9E,P1C5F19)
DTC SUMMARY MALFUNCTION DESCRIPTION This DTC indicates that a large current flowed in the inverter generator. The cause of this malfunction may be one of the following:
Area Main Malfunction Description
Hybrid vehicle transaxle assembly
Open or short circuit in the gen
Engine Coolant Temperature Sensor 1 Circuit Short to Battery or Open (P011515)
DESCRIPTION Refer to DTC P011511. Click here
HINT: When DTC P011515 is stored, the ECM enters fail-safe mode. During fail-safe mode, the engine coolant temperature is estimated to be 80°C (176°F) by the ECM. Fail-safe mode continues until a pass condition is detected.
DTC No. Detection
