Toyota Corolla Cross: Installation
INSTALLATION
CAUTION / NOTICE / HINT
COMPONENTS (INSTALLATION)
|
Procedure | Part Name Code |
.png) |
.png) |
.png) | |
|---|---|---|---|---|---|
|
1 | REAR CENTER SEAT OUTER BELT ASSEMBLY |
73350C | - |
- | - |
|
2 | REAR SEATBACK FRAME SUB-ASSEMBLY |
71017 | - |
- | - |
.png) |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
- | - |
|
Procedure | Part Name Code |
|
|
| |
|---|---|---|---|---|---|
|
3 | INSTALL SEPARATE TYPE REAR SEATBACK COVER |
71077S |
|
- | - |
|
4 | INSTALL SEPARATE TYPE REAR SEATBACK COVER |
71077S |
|
- | - |
|
5 | REAR SEAT HEADREST SUPPORT |
71931 | - |
- | - |
|
6 | REAR SEATBACK BOARD SUB-ASSEMBLY |
71701C | - |
- | - |
|
7 | REAR SEATBACK LOCK UPPER BEZEL |
72667A | - |
- | - |
|
8 | REAR SEAT SHOULDER BELT COVER |
73373 | - |
- | - |
|
9 | SEAT BELT ANCHOR COVER CAP |
73178A | - |
- | - |
|
10 | REAR SEAT CENTER ARMREST ASSEMBLY |
72830 | - |
- | - |
|
11 | CENTER ARMREST HINGE COVER |
72868B | - |
- | - |
|
12 | REAR SEAT CENTER HEADREST ASSEMBLY |
71940A | - |
- | - |
.gif)
|
*A | w/ Armrest |
*B | w/o Armrest |
|
*1 | SEPARATE TYPE REAR SEATBACK PAD |
- | - |
.png) |
N*m (kgf*cm, ft.*lbf): Specified torque |
- | - |
|
Procedure | Part Name Code |
|
|
| |
|---|---|---|---|---|---|
|
13 | REAR SEATBACK ASSEMBLY RH |
- |
|
- | - |
|
14 | REAR CENTER SEAT OUTER BELT ASSEMBLY |
73350C | - |
- | - |
|
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
- | - |
CAUTION / NOTICE / HINT
CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.
.png)
PROCEDURE
1. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY
Torque:
42 N·m {428 kgf·cm, 31 ft·lbf}
2. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY
3. INSTALL SEPARATE TYPE REAR SEATBACK COVER (w/ Armrest)
|
|
Click here |
4. INSTALL SEPARATE TYPE REAR SEAT BACK COVER (w/o Armrest)
|
|
Click here |
5. INSTALL REAR SEAT HEADREST SUPPORT
6. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY
7. INSTALL REAR SEATBACK UPPER LOCK BEZEL
8. INSTALL REAR SEAT SHOULDER BELT COVER
9. INSTALL SEAT BELT ANCHOR COVER CAP
10. INSTALL REAR SEAT CENTER ARMREST ASSEMBLY (w/ Armrest)
11. INSTALL CENTER ARMREST HINGE COVER (w/ Armrest)
12. INSTALL REAR SEAT HEADREST ASSEMBLY
13. INSTALL REAR SEATBACK ASSEMBLY RH
|
|
Click here |
14. CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
READ NEXT:
Removal
REMOVAL CAUTION / NOTICE / HINT COMPONENTS (REMOVAL)
Procedure Part Name Code
1 REAR CENTER SEAT OUTER BELT ASSEMBLY
73350C -
- -
2 BEN
Inspection
INSPECTION PROCEDURE 1. INSPECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY
(a) for LH Belt: (1) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
SEE MORE:
Fuel Pump Control Circuit Current Out of Range (P12D41D)
DESCRIPTION Refer to DTC P062712. Click here
DTC No. Detection Item
DTC Detection Condition Trouble Area
MIL Note
P12D41D Fuel Pump Control Circuit Current Out of Range
When the fuel pump control ECU operation duty ratio is 3 to 65%, overcurrent in the fuel
Freeze Frame Data
FREEZE FRAME DATA
FREEZE FRAME DATA
HINT:
When a DTC is stored, the freeze frame data stores the current vehicle
(sensor) state.
The freeze frame data cannot be cleared or updated until the recorded
DTCs are cleared.
(a) Using the GTS, the state of the vehicle (sensors) when the
